DRV8835 Dual Motor Driver Breakout

5,47 EUR

incl. 19 % USt zzgl. Versandkosten

Gewicht: 0.0025 kg

Hersteller: Pololu

Lagerbestand: 9

Lagernd, versandfertig in 24 Stunden.

Lagernd, versandfertig in 24 Stunden.

Art.Nr.: 2135
     

Produktbeschreibung

Kleiner 2 Kanal DC Motortreiber von Pololu mit dem TI DRV8835.
Pro Kanal stehen 1,2A Dauerstrom und 1,5A kurzzeitig zur Verfügung und dies bei einem Spannungsbereich von 2 - 11V.


Texas Instruments’ DRV8835 is a tiny dual H-bridge motor driver IC that can be used for bidirectional control of two brushed DC motors at 2 to 11 V. It can supply up to about 1.2 A per channel continuously and can tolerate peak currents up to 1.5 A per channel for a few seconds, making it an ideal driver for small motors that run on relatively low voltages. The DRV8835 is a great IC, but its small, leadless package makes it difficult for the typical student or hobbyist to use; our breakout board gives this driver the form factor of a 14-pin DIP package, which makes it easy to use with standard solderless breadboards and 0.1″ perfboards. Since this board is a carrier for the DRV8835, we recommend careful reading of the DRV8835 datasheet (208k pdf). The board ships populated with SMD components, including the DRV8835, and adds a FET for reverse battery protection.

This board is very similar to our DRV8833 dual motor driver carrier in operating voltage range and continuous current rating, but the DRV8835 has a lower minimum operating voltage, offers an extra control interface mode, and is 0.1″ smaller in each dimension. The DRV8833 has a higher peak current rating (2 A per channel vs 1.5 A), optional built-in current-limiting, and no need for externally supplied logic voltage.

Features

  • Dual-H-bridge motor driver: can drive two DC motors or one stepper motor
  • Motor supply voltage: 2–11 V
  • Logic supply voltage: 2–7 V
  • Output current: 1.2 A continuous (1.5 A peak) per motor
  • Motor outputs can be paralleled to deliver 2.4 A continuous (3 A peak) to a single motor
  • Two possible interface modes: IN/IN (outputs mostly mirror inputs) or PHASE/ENABLE (one pin for direction and another for speed)
  • 3V-compatible inputs
  • Undervoltage, overcurrent, and thermal shutdown
  • Reverse-voltage protection circuit
  • Compact size (0.7″×0.4″) with the form factor of a 14-pin DIP package

Motor and motor power connections are made on one side of the board and logic power and control connections are made on the other. Each control input is pulled low through a weak pull-down resistor (approximately 100 kΩ), so the driver will be in the IN/IN mode if the MODE pin is left disconnected, and the driver outputs will be disabled by default. The driver requires a motor voltage between 2 and 11 V and a logic voltage between 2 and 7 V; the logic voltage can typically be supplied by or shared with the controlling device.

The DRV8835 features two possible control modes: IN/IN and PHASE/ENABLE. The MODE pin determines the control interface. Setting the MODE pin high, either with a pull-up resistor or a driving-high I/O line, sets the driver to PHASE/ENABLE mode, where the PHASE pin determines the motor direction and the ENABLE pin can be supplied with a PWM signal to control the motor speed. This mode is generally easier to use as it only requires one PWM per channel, but it only allows for drive/brake operation. (Drive/brake operation usually provides a more linear relationship between PWM duty cycle and motor speed than drive/coast operation, and we generally recommend using drive/brake operation when possible.)

When the MODE pin is disconnected or low, the control interface is IN/IN, which allows for slightly more advanced control options. The following truth table show how to achieve drive/coast and drive/brake operation using the IN/IN control interface.

Real-world power dissipation considerations

The DRV8835 datasheet recommends a maximum continuous current of 1.5 A per motor channel. However, the chip by itself will overheat at lower currents. For example, in our tests at room temperature with no forced air flow, the chip was able to deliver 1.5 A per channel for approximately 15 seconds before the chip’s thermal protection kicked in and disabled the motor outputs, while a continuous current of 1.2 A per channel was sustainable for many minutes without triggering a thermal shutdown. The actual current you can deliver will depend on how well you can keep the motor driver cool. The carrier’s printed circuit board is designed to draw heat out of the motor driver chip, but performance can be improved by adding a heat sink. Our tests were conducted at 100% duty cycle; PWMing the motor will introduce additional heating proportional to the frequency.

Two 1×7-pin breakaway 0.1″ male headers are included with the DRV8835 dual motor driver carrier, which can be soldered in to use the driver with perfboards, breadboards, or 0.1″ female connectors. (The headers might ship as a single 1×14 piece that can be broken in half.) The right picture above shows the two possible board orientations when used with these header pins (parts visible or silkscreen visible). You can also solder your motor leads and other connections directly to the board.









































Kunden kauften auch

Crazyflie Nano Quadcopter - 6x15 mm Ersatzmotor (BC-CM-01-B)

Crazyflie Nano Quadcopter - 6x15 mm Ersatzmotor (BC-CM-01-B)

3,25 EUR

Spark Core mit u.FL Connector

Spark Core mit u.FL Connector

41,44 EUR

RedBear BLE Nano & MK20 USB Board (Bluetooth Low Energy Kit)

RedBear BLE Nano & MK20 USB Board (Bluetooth Low Energy Kit)

42,84 EUR

Ultraschall Entfernungsmesser HC-SR04

Ultraschall Entfernungsmesser HC-SR04

3,65 EUR

GHI XBee Adapter Modul

GHI XBee Adapter Modul

6,90 EUR