Artikel von HAOYU Electronics

10.1" 1024x600 TFT Display mit kapazitivem Touchscreen

HY101CTP - 10.1" 1024x600 TFT LCD Display mit kapazitiven Touchpanel (FT5406)

72,00 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



5" 800x480 TFT Display mit kapazitivem Touchscreen

HY050CTP-HD - 5" 800x480 TFT LCD Display mit kapazitiven Touchpanel (FT5206)

35,70 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

5" 800x480 TFT Display mit kapazitivem Touchscreen + FTDI FT811 EVE

The FT811CB is a development module for FTDI’s FT811, which is used to develop and demonstrate the functionality of the FT811 Embedded Video Engine, EVE.
The modules contains an FT811Q graphic controller and a 5" TFT color display with 800×480-pixel resolution.

42,66 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



7" 1024x600 IPS TFT Display mit kapazitivem Touchscreen

HY070CTP-HD-RGB IPS - 7" 1024x600 TFT LCD Display (IPS Panel) mit kapazitiven Touchpanel (FT5206)

54,00 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



7" 1024x600 TFT Display mit kapazitivem Touchscreen

HY070CTP-HD - 7" 1024x600 TFT LCD Display mit kapazitiven Touchpanel (FT5206)

49,50 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

7" 800x480 TFT Display mit kapazitivem Touchscreen

HY070CTP - 7" 800x480 TFT LCD Display mit kapazitiven Touchpanel (FT5206)

43,00 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

CE8301 - 5V USB Step-Up Schaltregler (0.9V-5V Eingang)

Fixed 5V Output Boost Regulator (step-up regulator) Module with standard USB Connector. Accepts Input voltage from 0.9V to upto 5V.

1,95 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

Gassensor für Luftqualität (MQ135)

Sensitive material of MQ135 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensors conductivity is more higher along with the gas concentration rising.

2,98 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

Gassensor Kohlenstoffmonoxid & Brennbares Gas (MQ9)

The Analog CO/Combustible Gas Sensor(MQ9) module is useful for gas leakage detecting, it used the sensitive material SnO2, which with lower conductivity in clean air. It make detection by method of cycle high and low temperature, and detect CO when low temperature (heated by 1.5V).

3,57 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

Gassensor LPG, i-butane, Methan, Alkohol, Wasserstoff (MQ5)

The MQ5 Gas Sensor module is useful for gas leakage detecting. It can detect LPG, i-butane, methane, alcohol, Hydrogen, smoke and so on. The sensitivity can be adjusted using the on-board potentiometer, and you'd use this sensor by reading the analog pin to which it is connected. Please use these sensors only in controlled experiments! Combustible gases and fumes are very dangerous! Here are details for some MQ gas sensor.

2,98 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

Gassensor Rauch/LPG/Kohlenstoffmonoxid (MQ2)

The Analog Smoke/LPG/CO Gas Sensor(MQ2) module utilizes an MQ-2 as the sensitive component and has a protection resistor and an adjustable resistor on board. The MQ-2 gas sensor is sensitive to LPG, i-butane, propane, methane, alcohol, Hydrogen and smoke. It could be used in gas leakage detecting equipments in family and industry. The resistance of the sensitive component changes as the concentration of the target gas changes.

2,98 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

HY-LPC1768-Mini-DK2 Development Kit + 2.8" TFT LCD

Das LPC1768-Mini-DK2 ist ein kleines Entwicklungsboard von Haoyu electronic. Es basiert auf dem NXP (NXP Semiconductors) LPC1700 Serien Prozessor (Cortex-M3 Core).

39,95 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



HY-MiniSTM32V Development Kit + 3.2" TFT Display

STM32 Entwicklungskit mit 3.2" TFT Touch-Display

35,95 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

MAX II EPM240 CPLD Dev Board

This is a smallest system includes power, clock, RST circuit, and all pins layout for MAX II EPM240 chip. You can use it as a EPM240 CPLD development platform for your CPLD project.

14,50 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

Mifare RFID (13.56 MHz) RC522 Leser-Modul

Mifare RC522 is the high integrated RFID card reader which works on non-contact 13.56MHz communication, is designed as a low power consumption, low cost and compact size read and write chip, is the best choice in the development of smart meters and portable hand-held devices.

4,95 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



MP1584 1-18V (3A) Step-Down Schaltregler

This DC/DC step-down voltage converter is based on MP1584, it converts input voltage between 4.5V and 28V into a smaller voltage between 0.8V and 18V, capable of driving a 3A load with excellent line and load regulation.

2,50 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



MP2307 1-17V (1.8A) Step-Down Schaltregler

This DC/DC step-down voltage converter is based on MP2037, it converts input voltage between 4.5V and 23V into a smaller voltage between 1V and 17V, capable of driving a 1.8A load with excellent line and load regulation.

2,50 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



MPU6050 3-Achsen Beschleunigungssensor + Gyro 6-DOF IMU

Das MPU-6050 ist ein MEMS 3-Achsen Gyroskop und 3-Achsen Beschleunigungssensor zugleich. 

Der MPU6050 ist mit einem I2C Interface ausgestattet und kann somit recht einfach an einen Mikrocontroller angeschlossen werden.

4,50 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



MPU9255 3-Achsen Beschleunigungssensor + Gyro + Magnetometer 9-DOF IMU

The MPU-9250 is a 9-axis MotionTracking device that combines a 3-axis gyroscope, 3-axis accelerometer, 3-axis magnetometer and a Digital Motion Processor™ (DMP) all in a small 3x3x1mm package available as a pin-compatible upgrade from the MPU-6515.

9,50 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



OV7670 Kamera Modul mit AL433 FIFO

The OV7670 is a low cost image sensor + DSP that can operate at a maximum of 30 fps and 640 x 480 ("VGA") resolutions, equivalent to 0.3 Megapixels. The captured image can be pre-processed by the DSP before sending it out. This preprocessing can be configured via the Serial Camera Control Bus (SCCB). It's very useful for Electronic lovers, you can use the camera with STM32 or even with Arduino.

14,50 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



PIR Bewegungssenor HC-SR501

Human Sensor Module Pyroelectric Infrared
Arbeitsspannung: DC 4.5-20 V

3,00 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

PIR Bewegungssenor Mini HC-SR505

HC-SR505 Mini PIR Motion Sensor is based on infrared technology and it can automatic control by itself with high sensitivity and high reliability. Because of the minimum size and low-power operation mode, it widely used in various of automatic electronic equipment, especially battery-powered automatic products.

3,00 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

Relais Modul (4-Kanal 10A)

A Relay is a digital switch to control much higher voltages and currents than your normal Arduino boards does. When inputs a logic voltage, the relay will switch to allow current to flow or cutoff, depending on your wiring. A Relay usually consists of a coil, 1 common terminal, 1 normally closed terminal and one normally open terminal. When the coil is energized, the common terminal and the normally open terminal will have continuity.

4,85 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

Seriell MP3 Player Board (YX5200-24SS)

DFPlayer Mini is a compact and inexpensive MP3 module that can be connected directly to the speaker. Module can be used alone with battery power supply, speaker and keypad, or through the serial port control, as the Arduino UNO or any microcontroller with a serial port module. The module itself perfectly integrated hardware decode MP3, WAV, WMA's. While the software supports TF card driver to support FAT16, FAT32 file system. Can be done by simple serial command plays the specified music, as well as how to play music and other functions, easy to use, stable and reliable!

4,95 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



Stereo 3W Audioverstärker - PAM8403

- Power: DC 3.6V - 5.5V
- Output power: 3W +3 W
- Signal-to-noise ratio: 90dB
- Efficiency:> 90%

1,85 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

STM32F030F4P6 ARM Cortex-M0 Development Board

This board is a STM32F030F4P6 Minimum Systerm Board(Cortex-M0). The target MCU is STM32F030F4P6 that is provided by ST. It is a ARM 32-bit Cortex™-M0 CPU, frequency up to 48 MHz, high-speed embedded memories . As a minimal ready-to-run system, this board integrates micorUSB power supply interface, ISP/SWD programming/debugging interface, boot mode selection and so on to take you into the ARMCortex world easy.

4,25 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

STM32F103C8T6 ARM Cortex-M3 Development Board

New STM32 Minimum System Development Board Module For Arduino - STM32F103C8T6, A Medium-density performance line ARM-based 32-bit MCU with 64 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces. Let’s begin our Arduino work by using it.

4,85 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



STM32F103TBU6 ARM Cortex-M3 Development Board

HY-TinySTM103T is entry level development board for the ARM Cortex M3 family of devices produced by ST Microelectronics Inc. With HY-TinySTM103T you can explore the features of STM32 family on budget, the board have everything necessary to build simple applications: USB port where power is taken and power supply circuit, reset and oscillator circuits, SWD/ISP for programming and debugging, one status LEDs and reset button.

4,65 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

TCS3200 Farbsensor-Modul

TCS3200 chip is designed to detect the color of light incident on it. It has an array of photodiode (a matrix of 8x8, so a total 64 sensors).

4,76 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

TDA8932 - Mono 35W Audioverstärker Board

The board uses a high-performance digital amplifier chip TDA8932, small size, high efficiency, high power, good sound quality, without additional installation of heat sink, very suitable for passive speaker transformation.

6,00 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.

TP4056 - Micro USB 5V 1A Lithium Battery Charger with Protection

This tiny module is perfect for charging single cell 3.7V 1 Ah or higher LiPo cells such as 16550s that don't have their own protection circuit.

2,50 EUR incl. 19 % USt zzgl. Versandkosten

Nicht auf Lager.



Ultraschall Entfernungsmesser HC-SR04

Der Ultraschall Entfernungssensor HC-SR04 eignet sich zur Messung im Bereich zwischen 2cm und ca. 3m (Auflösung von ca. 3mm).

3,65 EUR incl. 19 % USt zzgl. Versandkosten

Lagernd, versandfertig in 24 Stunden.