Pololu Pushbutton Power Switch LV

6,32 EUR

incl. 19 % USt zzgl. Versandkosten

Gewicht: 0.0010 kg

Hersteller: Pololu

Lagerbestand: 0

Nicht auf Lager.

Nicht auf Lager.

Art.Nr.: 751


Mit dieser kleinen Schaltung ist es möglich einen Schalter durch einen Taster zu ersetzen.
Die zu schaltende Spannung kann im Bereich von 2,5 - 7 Volt liegen, der maximale Strom durch den MosFET ist mit 10A angegeben.

The Pololu Pushbutton Power Switch is a compact, solid-state power switch controlled by a momentary pushbutton switch. Because the switched current does not flow through the mechanical switch, a large variety of small, low-power switches can be used to control a substantial amount of power. The use of momentary pushbutton switches also allows multiple switches to be used in parallel to control the power to one load. The solid-state switch also allows the load to turn off its own power, which can be beneficial when used with battery chemistries sensitive to over-discharging. Please note that this switch has several drawbacks when compared to mechanical switches, so please be sure you fully understand this product before using it in your system.

Benefits and Limitations

The Pololu Pushbutton Power Switch works well in its intended application as a DC power switch for small robots, but because it is fundamentally different from a mechanical power switch, the benefits and drawbacks of the components must be fully considered.

Benefits over mechanical switches:

  • Compact size
  • Allows multiple (parallel) switches for improved user interface
  • Better turn-on characteristics than a bouncing mechanical switch
  • Limited LC spikes for low-resistance loads
  • Allows self-shutoff
  • Breadboard and perfboard compatible

Drawbacks compared to mechanical switches:

  • Switch is one-directional (inherent body diode in MOSFET)
  • Limited operating voltage range
  • Switches DC only (does not maintain state through power disruptions or excessive noise)
  • No complete isolation in off state


  • Dimensions: 0.4" x 0.9" x 0.125" (without header pins and pushbutton installed)
  • Operating voltage: 4.5-20 V (SV version), 2.5-7.0 V (LV version)
  • Maximum current: 10 A (see MOSFET datasheets)
  • Weight without included pushbutton: 0.030 oz (0.85 g)
  • Weight with included pushbutton: 0.035 oz (1.0 g)
  • Draws very little current in off state (typically under 0.01 μA)

Typical Applications

The Pololu Pushbutton Power Switch can fit in an 18-pin DIP (dual in-line package) footprint, making it compatible with solderless breadboards and perforated printed circuit boards with standard 0.1" spacing. For such applications, the included male header pins can be soldered to the switch PCB as shown in the picture to the right. Alternatively, wires can be soldered directly to the switch PCB for non-breadboard applications. For high-current applications, make sure that the wires can safely carry the current. Two pads/pins are provided for each of the power nodes, and multiple pads should be used for applications drawing over 5 A.

The included pushbutton switch can be used to trigger the switch. Alternatively, a separate pushbutton, such as a remote panel-mounted unit, can be used instead. Multiple pushbuttons can be wired in parallel for multiple control points, and each of the parallel pushbuttons will be able to turn the switch on or off. The latching circuit performs some button debouncing, but pushbuttons with excessive bouncing (several ms) might not function well with this product.

Principles of Operation

The Pololu Pushbutton Power Switch has two main components: a P-channel power MOSFET that switches the load current and a latching circuit that controls the gate of the MOSFET.

The overall switch performance is determined by the MOSFET characteristics, which are specified in their datasheets. The standard voltage version uses the FDS6679AZ (421k pdf); the low-voltage version uses the FDS4465 (141k pdf). The latching circuit is designed to operate over a wide range of voltages and to draw very little current in the off state (typically under 0.01 μA). In the on state, the switch pulls the MOSFET gate to within 0.2 V of ground so that the MOSFET’s Vgs can be approximated as the supply voltage.

The latching circuit controlling the power MOSFET includes an OFF input that can be used by the target device to shut off its own power. The internal structure of this input is shown to the right. Applying more than approximately 1 V to the OFF pin will cause the power switch to turn off. The maximum voltage for the OFF pin is 30 V independent of the switch voltage (VIN).

Characteristics at Limits of Operating Range

The switch operating range is limited by the ability to change state reliably. At low voltages, the switch is difficult to turn on, and the switch will turn itself off once the voltage falls far enough (typically 3 V and 1.5 V for the SV and LV versions, respectively). At high voltages, the switches become difficult to turn off. The reliability of turning off is affected by a combination of the supply voltage, the amount of bouncing on the pushbutton switch, and the amount of noise on the supply line. For applications at the high end of the operating range, tests should be performed to ensure that the device can properly turn off.

Kunden kauften auch

Pololu 9V Step-Up Schaltregler U3V12F9

Pololu 9V Step-Up Schaltregler U3V12F9

4,34 EUR

Testkabel / Jumper Wires M/M 200mm (für Breadboards )

Testkabel / Jumper Wires M/M 200mm (für Breadboards )

2,75 EUR

ADS1115 - 4 Kanal 16-Bit ADC (Gain Amp.)

ADS1115 - 4 Kanal 16-Bit ADC (Gain Amp.)

16,54 EUR

PIC-ICSP Adapter

PIC-ICSP Adapter

3,51 EUR

MultiMount für Arduino, pcDuino, BeagleBone, Raspberry Pi & Cubieboard

MultiMount für Arduino, pcDuino, BeagleBone, Raspberry Pi & Cubieboard

3,95 EUR