Stereo 3.7W Class D Audioverstärker - MAX98306

11,90 EUR

incl. 19 % USt zzgl. Versandkosten

Gewicht: 0.0060 kg

Hersteller: Adafruit Industries

Lagerbestand: 0

Nicht auf Lager.

Nicht auf Lager.

Art.Nr.: ADA987
     

Produktbeschreibung

Stereo 3,7W Class D Audio Verstärker mit einem Versorgungsspannung von 2,7-5,5V.
Der Verstärker hat einen Wirkungsgrad bis zu 90% bei Verwendung von 8 Ohm Lautsprechern.

Vollständige Englische Beschreibung:

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, its incredibly efficient (over 90% efficient when driving an 8Ω speaker at over a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. This board is a welcome upgrade to basic "LM386" amps!

The inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the R- and L- to ground. The outputs are "Bridge Tied" - that means they connect directly to the outputs, no connection to ground. The output is a 360KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly.

Comes with a fully assembled and tested breakout board with 1.0uF input capacitors. We also include header to plug it into a breadboard, 3.5mm screw-terminal blocks so you can easily attach/detach your speakers, and a 2x4 header + jumper to change the amplifier gain on the fly. You will be ready to rock in 15 minutes! Speakers are not included, use any 3ohm or greater impedance speakers.

  • Output Power: 3.7W at 3Ω, 10% THD, 1.7W at 8Ω, 10% THD, with 5V Supply
  • Passes EMI limit unfiltered with up to 12 inches (30 cm) of speaker cable
  • High 83dB PSRR at 217Hz
  • Spread-Spectrum Modulation and Active Emissions Limiting
  • Five pin-selectable gains: 6dB, 9dB, 12dB, 15dB and 18dB. Select with a jumper or by setting the G and G' breakout pins (see schematic for breakout board showing gain pin settings for details)
  • Excellent click-and-pop suppression
  • Thermal and short-circuit/over-current protection
  • Low current draw: 2mA quiescent and 10uA in shutdown mode

Kunden kauften auch

DRV8835 Dual Motor Driver Breakout

DRV8835 Dual Motor Driver Breakout

5,47 EUR

Short Crust Plus Gehäuse für Raspberry Pi 2, 3 & B+ (weiß)

Short Crust Plus Gehäuse für Raspberry Pi 2, 3 & B+ (weiß)

14,40 EUR

Breakout Board mit Kondensatormikrofon

Breakout Board mit Kondensatormikrofon

7,01 EUR

Schrittmotor NEMA 17: Bipolar, 200 Steps, 42x42mm, 12V, 0.33A

Schrittmotor NEMA 17: Bipolar, 200 Steps, 42x42mm, 12V, 0.33A

16,36 EUR