Product from Adafruit Industries

12mm Diffused Digital RGB LED Pixels (Strand of 25) -  WS2801

12mm Diffused Digital RGB LED Pixels (Strand of 25) - WS2801

RGB Pixels are digitally-controllable lights you can set to any color, or animate. Each RGB LED and controller chip is molded into a 'dot' of silicone. The dots are waterproof and rugged. There are four flanges molded in so that you can 'push' them into a 12mm drill hole in any material up to 1.5mm/0.06" thick. They're typically used to make outdoor signs. Compared to our other 20mm LED dots, these are diffused 8mm LEDs so they are not as bright but they color mix a little nicer.

40,46 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

12V EL wire/tape inverter

12V EL wire/tape inverter

This is an inverter for EL wire and tape, similar to our pocket inverters, except it is a brick that takes 12V input instead of 2 AA batteries. This means its good for 'fixed' installations since you can just plug it into a 12V wall adapter. It's also good for portable projects where you want to have a big battery pack like a 8xAA holder which will last 4-5 times longer than just 2xAA's. It is also more powerful, and can drive twice as much EL as the 2xAA inverter! Another nice thing about this inverter is it's a potted brick, so its quieter than the 'open' inverters with a switch.

4,53 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



16mm Illuminated Pushbutton - Green Latching On/Off Switch

16mm Illuminated Pushbutton - Green Latching On/Off Switch

A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good.

1,37 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



16mm Illuminated Pushbutton - Green Momentary

16mm Illuminated Pushbutton - Green Momentary

A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good.

1,25 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



16x32 RGB LED matrix panel

16x32 RGB LED matrix panel

Bring a little bit of Times Square into your home with this 16 x 32 RGB LED matrix panel. These panels are normally used to make video walls, here in New York we see them on the sides of busses and bus stops, to display animations or short video clips.

24,99 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



2.8

2.8" TFT LCD with Touchscreen Breakout Board w/MicroSD Socket

Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful! 240x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

32,49 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

2.8

2.8" TFT Touch Shield for Arduino v2

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. It has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

37,14 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



3D printing - Skill badge, iron-on patch

3D printing - Skill badge, iron-on patch

You can 3D print! Adafruit offers a fun and exciting "badges" of achievement for electronics, science and engineering. We believe everyone should be able to be rewarded for learning a useful skill, a badge is just one of the many ways to show and share.

3,92 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

4-channel I2C-safe Bi-directional Logic Level Converter - BSS138

4-channel I2C-safe Bi-directional Logic Level Converter - BSS138

Replacement: 4-Channel Level-Shifter

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V.

3,62 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



8-channel Bi-directional Level Converter - TXB0108

8-channel Bi-directional Level Converter - TXB0108

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V.

7,32 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685

Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685

You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? You could give up OR you could just get this handy PWM and Servo driver breakout.

13,69 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit 24-Channel 12-bit PWM LED Driver - SPI Interface - TLC5947

Adafruit 24-Channel 12-bit PWM LED Driver - SPI Interface - TLC5947

For all of you out there who want to control 24 channels of PWM, we salute you! We also would like you to check out this breakout board for the TLC5947 PWM driver chip. This chip can control 24 separate channels of 12-bit PWM output. Designed (and ideal) for LED control, this board is not good for driving servos. If you need to drive servos, we have a controller for that over here.

13,90 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit 6-pin AVR ISP Breadboard Adapter Mini Kit

Adafruit 6-pin AVR ISP Breadboard Adapter Mini Kit

It's rare to find a mini kit so elegant, it deserves its own Haiku. A simple breakout, 2x3 box header in the center, two 1x3's on the side. Plugs into any breadboard for neat wiring (in both nifty and clean senses of the word).

0,88 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit BBB Case - Enclosure for Beagle Bone Black

Adafruit BBB Case - Enclosure for Beagle Bone Black

We are thrilled to release Adafruit's lovely Beagle Bone Black case, designed by Mike Doell (who made our really terrific Raspberry Pi enclosures as well). We wanted a beautiful, elegant case, not just functional but also something you'd really like having on your desk. Gaze lovingly at its square modern ahape & its glossy clear cover!

9,25 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit Bone Box - Enclosure for Beagle Bone

Adafruit Bone Box - Enclosure for Beagle Bone

Pack up your Beagle Bone in this lovely clear plastic case. We designed this case to be the ideal enclosure, with plenty of elegant details to make it useful to you!

18,99 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit CC3000 WiFi Breakout with Onboard Antenna

Adafruit CC3000 WiFi Breakout with Onboard Antenna

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So we shied away from carrying any general purpose microcontroller-friendly WiFi boards.

NO LONGER!

The CC3000 hits that sweet spot of usability, price and capability. It uses SPI for communication (not UART!) so you can push data as fast as you want or as slow as you want. It has a proper interrupt system with IRQ pin so you can have asynchronous connections. It supports 802.11b/g, open/WEP/WPA/WPA2 security, TKIP & AES. A built in TCP/IP stack with a "BSD socket" interface. TCP and UDP in both client and server mode, up to 4 concurrent sockets. It does not support "AP" mode, it can connect to an access point but it cannot be an access point.

We wrapped this little silver modules in a tidy breakout board. It has an onboard 3.3V regulator that can handle the 350mA peak current, and a level shifter to allow 3 or 5V logic level. The antenna layout is identical to TI's suggested layout and we're using the same components, trace arrangement, and antenna so the board maintains its FCC emitter compliance (you'll still need to perform FCC validation for a finished product, but the WiFi part is taken care of). Even though it's got an onboard antenna we were pretty surprised at the range, as good as a smartphone's.

Each order comes with one fully assembled and tested breakout and a small stick of header you can use to solder in and plug into a breadboard. We don't have a detailed tutorial yet but to get you started, we've got a fully working Arduino library that is based off of TI's codebase but adapted for use with the AVR. We also have example code showing how to scan the SSID's, connect to your access point and run DHCP, do a DNS lookup to IP address, ping a site and connect to a remote TCP socket such as a website and print out the page.

Please note the hardware is good, but the library code does not yet support all of the CC3000's functionality. SSID scanning, connection, DHCP, DNS lookup, ping, and UDP/TCP client connections (eg connect to a website and grab data) all work and are tested with example code. UDP/TCP server connections are not supported yet! As we try to complete the functionality, check or subscribe to the github repo for instant updates. For now we suggest this module and codebase for people with some programming and microcontroller experience

For use with Arduino Uno & Mega only at this time - we'll try to get the code ported to the Leonardo/Due at some point but no ETA. To wire it up: Connect Vin to 5V and Ground to common ground. SCLK connects to your Arduino's hardware SPI Clock pin, MOSI to the SPI MOSI pin, MISO to the SPI MISO pin, CS to digital #10, VBEN to digital #5, and IRQ to digital #3

31,99 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit CC3000 WiFi Shield with Onboard Antenna

Adafruit CC3000 WiFi Shield with Onboard Antenna

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So we shied away from creating or developing a WiFi Arduino shield.

36,57 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit DC Boarduino Kit (Arduino compatible)

Adafruit DC Boarduino Kit (Arduino compatible)

This is a Arduino clone from LadyAda with ATmega328.
It is specialy made for use it on a solderless breadboard.

17,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit GEMMA - Miniature wearable electronic platform

Adafruit GEMMA - Miniature wearable electronic platform

Love FLORA but want a bite-sized version? Look no further, GEMMA is a tiny wearable platform board with a lot of might in a 1" diameter package. Powered by a Attiny85 and programmable with an Arduino IDE over USB, you'll be able to realize any wearable project!

7,28 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit Half-size Perma-Proto Raspberry Pi Breadboard PCB Kit

Adafruit Half-size Perma-Proto Raspberry Pi Breadboard PCB Kit

We put a PermaProto half sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x13 pin header in and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk.

5,66 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit Micro Lipo - USB LiIon/LiPoly charger - v1

Adafruit Micro Lipo - USB LiIon/LiPoly charger - v1

Oh so adorable, this is the tiniest little lipo charger, so handy you can keep it any project box! Its also easy to use. Simply plug in the gold plated contacts into any USB port and a 3.7V/4.2V lithium polymer or lithium ion rechargeable battery into the JST plug on the other end. There are two LEDs - one red and one green. While charging, the red LED is lit. When the battery is fully charged and ready for use, the green LED turns on. Seriously, it could not get more easy.

5,66 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit Mini 8x8 LED Matrix w/I2C Backpack-Yellow

Adafruit Mini 8x8 LED Matrix w/I2C Backpack-Yellow

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins. That's a lot of pins, and there are driver chips like the MAX7219 that can control a matrix for you but there's a lot of wiring to set up and they take up a ton of space. Here at Adafruit we feel your pain! After all, wouldn't it be awesome if you could control a matrix without tons of wiring? That's where these adorable LED matrix backpacks come in. We have them in two flavors - a mini 8x8 and a 4-digit 0.56" 7-segment. They work perfectly with the matrices we stock in the Adafruit shop and make adding a bright little display trivial.

The matrices use a driver chip that does all the heavy lifting for you: They have a built in clock so they multiplex the display. They use constant-current drivers for ultra-bright, consistent color (the images above are photographed at the dimmest setting to avoid overloading our camera!), 1/16 step display dimming, all via a simple I2C interface. The backpacks come with address-selection jumpers so you can connect up to four mini 8x8's or eight 7-segments (or a combination, such as four mini 8x8's and four 7-segments, etc) on a single I2C bus.

The product kit comes with:

A bit of soldering is required to attach the matrix onto the backpack but its very easy to do and only takes about 5 minutes.

Of course, in classic Adafruit fashion, we also have a detailed tutorial showing you how to solder, wire and control the display. We even wrote a very nice library for the backpacks so you can get running in under half an hour, displaying images on the matrix or numbers on the 7-segment. If you've been eyeing matrix displays but hesitated because of the complexity, his is the solution you've been looking for!

6,66 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit - v2.0

Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit - v2.0

Here is a design for a full-featured motor shield that will be able to power many simple to medium-complexity projects.

  • 2 connections for 5V 'hobby' servos
  • Up to 4 bi-directional DC
  • Up to 2 stepper motors

18,26 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit NeoPixel Shield for Arduino - 40 RGB LED Pixel Matrix

Adafruit NeoPixel Shield for Arduino - 40 RGB LED Pixel Matrix

Put on your sunglasses before putting this shield onto your 'duino - 40 eye-blistering RGB LEDs adorn the NeoPixel shield for a blast of configurable color. Arranged in a 5x8 matrix, each pixel is individually addressable. Only one pin (Digital #6) is required to control all the LEDs. You can cut a trace and use nearly any other pin if you need some customization.

25,59 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit PCB Ruler - 6

Adafruit PCB Ruler - 6"

The first time you soldered up a surface mount component you may have been surprised "these are really small parts!" and there's dozens of different names too!

4,53 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit Pi Cobbler Breakout Kit for Raspberry Pi

Adafruit Pi Cobbler Breakout Kit for Raspberry Pi

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi Cobbler from Adafruit, which can break out all those tasty power, GPIO, I2C and SPI pins from the 26 pin header onto a solderless breadboard. This mini kit will make "cobbling together" prototypes with the Pi super easy.

7,88 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit Pi Dish for Raspberry Pi - Includes Breadboard

Adafruit Pi Dish for Raspberry Pi - Includes Breadboard

By popular demand! We now have a way to attach a Raspberry Pi computer to a plastic 'dish' with a full-sized breadboard.

21,42 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit Pi T-Cobbler Breakout Kit for Raspberry Pi

Adafruit Pi T-Cobbler Breakout Kit for Raspberry Pi

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi T-Cobbler from Adafruit, which can break out all those tasty power, GPIO, I2C and SPI pins from the 26 pin header onto a solderless breadboard. This mini kit will make "cobbling together" prototypes with the Pi super easy. Designed for Raspberry Pi Model B Revision 1 or Revision 2.

7,57 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit Proto Cape Kit for Beagle Bone & Beagle Bone Black

Adafruit Proto Cape Kit for Beagle Bone & Beagle Bone Black

Add some circuitry to your Beagle Bone or Beagle Bone Black with our lovely Proto Cape. If you have a 'Bone you need one of these! This PCB fits neatly on top of a Beagle Bone, without getting in the way of the Ethernet jack, and provides a breakout to both 46 pin headers - with individual numbering to keep them straight. We also threw down some strips to access the 5V and 3V power supplies as well as two SMT breakouts, one for SOIC-8's and one for SOT-23's.

9,25 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit Prototyping Pi Plate Kit for Raspberry Pi

Adafruit Prototyping Pi Plate Kit for Raspberry Pi

Prototyping Pi Plate Kit for Raspberry Pi

15,82 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit RGB Negative 16x2 LCD+Keypad Kit for Raspberry Pi

Adafruit RGB Negative 16x2 LCD+Keypad Kit for Raspberry Pi

This new Adafruit Pi Plate makes it easy to use an RGB 16x2 Character LCD. We really like the RGB Character LCDs we stock in the shop. (For RGB we have RGB negative and RGB positive.) Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another 3 to control the RGB backlight for a total of 9 pins. That's nearly all the GPIO available on a Pi!

23,75 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit RGB Positive 16x2 LCD+Keypad Kit for Raspberry Pi

Adafruit RGB Positive 16x2 LCD+Keypad Kit for Raspberry Pi

This new Adafruit Pi Plate makes it easy to use an RGB 16x2 Character LCD. We really like the RGB Character LCDs we stock in the shop. (For RGB we have RGB negative and RGB positive.) Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another 3 to control the RGB backlight for a total of 9 pins. That's nearly all the GPIO available on a Pi!

23,75 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit RGB Positive 16x2 LCD+Keypad Kit for Raspberry Pi with Standard LCD 16x2 + extras - white on blue

Adafruit RGB Positive 16x2 LCD+Keypad Kit for Raspberry Pi with Standard LCD 16x2 + extras - white on blue

This new Adafruit Pi Plate makes it easy to use a blue and white 16x2 Character LCD. We really like the 16x2 Character LCDs we stock in the shop. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another 1 to control the backlight for a total of 7 pins. That's nearly all the GPIO available on a Pi!

19,04 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit Trinket - Mini Microcontroller - 3.3V Logic

Adafruit Trinket - Mini Microcontroller - 3.3V Logic

Trinket may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny85, a little chip with a lot of power. We wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation.

7,39 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit Trinket - Mini Microcontroller - 5V Logic

Adafruit Trinket - Mini Microcontroller - 5V Logic

Trinket may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny85, a little chip with a lot of power.

7,39 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adafruit Ultimate GPS Breakout (66 channel w/10 Hz)

Adafruit Ultimate GPS Breakout (66 channel w/10 Hz)

  • -165 dBm sensitivity, 10 Hz updates, 66 channels
  • 5V friendly design and only 20mA current draw
  • Breadboard friendly + two mounting holes
  • RTC battery-compatible
  • Built-in datalogging
  • PPS output on fix
  • >25Km altitude
  • Internal patch antenna + u.FL connector for external active antenna
  • Fix status LED

39,62 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit Ultimate GPS Logger Shield - Includes GPS Module

Adafruit Ultimate GPS Logger Shield - Includes GPS Module

Brand new and better than ever, we've replaced our Adafruit GPS shield kit with this assembled shield that comes with an Ultimate GPS module.

46,44 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit USB Boarduino Kit V2.0 (Arduino compatible)

Adafruit USB Boarduino Kit V2.0 (Arduino compatible)

This clone acts just like an Arduino, and works with the latest Arduino software. For many projects it can even be preferable! The kit includes all parts necessary, the assembly is straightforward and well documented, using just a soldering iron anyone can complete it within 10 or 15 minutes.

23,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adafruit USB to TTL Serial Cable for Raspberry Pi

Adafruit USB to TTL Serial Cable for Raspberry Pi

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USB<->Serial conversion chip and at the end of the 36" cable are four wire - red power, black ground, white RX into USB port, and green TX out of the USB port. The power pin provides the 500mA direct from the USB port and the RX/TX pins are 3.3V level for interfacing with the most common 3.3V logic level chipsets.

8,93 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Adapter: female DC plug 2.1mm to screw terminal block

Adapter: female DC plug 2.1mm to screw terminal block

If you need to connect a DC power wall wart to a board that doesn't have a DC jack - this adapter will come in very handy! There is a 2.1mm DC jack on one end, and a screw terminal block on the other. The terminals are labeled with positive/negative assuming a positive-tip configuration (which is the most common)

1,90 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Adapter: USB-A Jack to 2.1/5.5mm DC jack (female)

Adapter: USB-A Jack to 2.1/5.5mm DC jack (female)

This little dongle will let you connect one of our 5V adapters to something that expects to connect to USB. The premise is simple - one end has a USB A female jack and the other has a 'standard' 5.5mm OD/2.1mm ID barrel jack with center positive polarity.

2,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

ADS1015 12-Bit ADC - 4 Channel with Programmable Gain Amplifier

ADS1015 12-Bit ADC - 4 Channel with Programmable Gain Amplifier

For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1015 provides 12-bit precision at 3300 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels.

9,25 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



ADS1115 - 4 channel 16-Bit ADC (Gain Amp.)

ADS1115 - 4 channel 16-Bit ADC (Gain Amp.)

For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C.

14,46 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Altoids Gum sized tin

Altoids Gum sized tin

Ever since Altoids discontinued the Gum version, its been hard to get tins. So we went and got a whole mess of them custom made! These tins are exactly the same shape and size as the old Altoids gum tins but they are blank and we got the bottom flattened instead of rounded (so it fits things better)

1,90 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Altoids mints sized tin

Altoids mints sized tin

Useful for larger electronic projects, including the YBox2 kit

  • Top lid outer (not lip): 2.36" (59.9mm) x 3.75"(95mm)
  • Tin bottom: 2.3" (58.75mm) x 3.7"(93.9mm)
  • Inner: 2.24" (56.9mm) x 3.6"(91.5mm)
  • Height bottom section: 0.83" (21.28mm)
  • Height top section: "0.36 (9.26mm)
  • Corner radius .55" (14mm)

2,38 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager



Android - Skill badge, iron-on patch

Android - Skill badge, iron-on patch

You hacked, modded or made something with Android! Adafruit offers a fun and exciting "badges" of achievement for electronics, science and engineering. We believe everyone should be able to be rewarded for learning a useful skill, a badge is just one of the many ways to show and share.

2,98 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Arduino - Skill badge, iron-on patch

Arduino - Skill badge, iron-on patch

This is the "I'm learning Arduino" badge for use with educators, classrooms, workshops, Maker Faires, TechShops, Hackerspaces, Makerspaces and around the world to reward beginners on their skill building journey!

3,62 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Atmega32u4 Breakout Board+

Atmega32u4 Breakout Board+

Toss out those FTDI cables and go USB-native with the ATmega32u4. After many months of back-orders, we finally received a shipment of these little guys and are excited to offer our breakout board. The little dev board keeps it simple, with just the bare essentials:

  • Atmega32u4 - AVR core with USB capability. 32K flash, 2.5K RAM running at 16MHz
  • We put an open-source, avrdude compatible bootloader on there, which takes 4K. You can always remove it
  • Standard AVR 6-pin ISP connector for direct programming (when you need the extra space)
  • Big Bootload/Reset button
  • 500mA fuse on the USB power line
  • Power LED and 'user' LED (also indicates when the bootloader is active)
  • Fits nicely in any breadboard
  • 4 mounting holes
This breakout board is best for those who have familiarity with some microcontrollers and are comfortable with writing code in C. This board doesn't come with any 'learn to program' tutorials! If this is your first time with a microcontroller, we suggest going with an Arduino which is easier. Then when you want to upgrade, check this out.

Plug it in, connect a mini-B USB cable and you can start writing code immediately. With the built-in bootloader you don't even need an AVR programmer. We suggest checking out the LUFA library to get started with the USB core as nearly every kind of device has an example already.

For more information, including files, check out the product page including why you'd want to use a Teensy or this board.

17,25 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Beagle Bone - Skill Badge, iron-on patch

Beagle Bone - Skill Badge, iron-on patch

Beagle Bone - Skill badge, iron-on patch

2,98 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Blue Electroluminescent (EL) Wire - 2.5m

Blue Electroluminescent (EL) Wire - 2.5m

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid blue. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to a project, not as bright as LEDs but uses a lot less power!

10,98 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.