Product from Arduino

Arduino ADK Rev3

The Arduino ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface to connect with Android based phones.

Arduino BT (Bluetooth)

The Arduino BT is an Arduino board with built-in bluetooth module, allowing for wireless communication.

Arduino Duemilanove - Sale

The new Arduino Uno is now available.

The Arduino Duemilanove ("2009") is a microcontroller board based on the ATmega328.

Arduino Ethernet Shield - PoE module

This Ag9120 module could be used with the Arduino Ethernet shield (newest revision). The PoE module is designed to extract power from a conventional twisted pair Category 5 Ethernet cable, conforming to the IEEE 802.3af Power-over-Ethernet (PoE) standard.

Arduino Ethernet without PoE module

The Arduino Ethernet is a microcontroller board based on the Arduino Uno, and incorporating a WizNet W5100 TCP/IP Embedded Ethernet Controller. It can be programmed like an Uno via a six-pin FTDI -style serial connector. The Arduino USB 2 Serial adapter or any FTDI-style USB-to-serial connector can be used to program it.

Arduino Mega

Discontinued - new board Mega 2560


The new Arduino Mega is using an ATMEGA1280 processor.
128KB of Flash
8KB RAM
4KB EEPROM

Arduino Mega 2560 ADK Kit

Special kit for using the Arduino Mega ADK with an Android device

Arduino Mega 2560 Rev. 3

The new Arduino Mega is using an ATMEGA2560 processor.
256KB of Flash
8KB RAM
4KB EEPROM

It has 53 IO (including 4 HW UARTs, 14 PWMs, I2C bus) and 16 Analog Input pins.
It can mount and use most of the Arduino Shields.

Arduino Mega ADK

The Arduino ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface to connect with Android based phones.

Arduino Mini

Mini - This is the smallest Arduino board. It works well in a breadboard or for applications in which space is at a premium. It connects to the computer using the Mini USB Adapter.

Arduino Uno Rev 2 SMD

The Arduino Uno R3 is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

Arduino Uno Rev 3

The Arduino Uno R3 is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

Arduino USB to Serial Converter

This board converts a USB connection into 5 volt TX and RX that you can connect straight to the Arduino Mini or other microcontrollers.

Box for Arduino

Box for Arduino: Plastic (flame retardant) box that could fit an Arduino Board (Duemilanove-Diecimila-NG or MEGA), an ETH shield and a battery.

Ethernet-Shield (Arduino)

ETH Shield with micro SD card connector
This new ETH shield had a lot of new improvements. It is compatible
with the MEGA board, It has an on board micro SD card connector and
an on-board reset controller.

The Arduino Ethernet shield allows an Arduino board to connect to a LAN using the Ethernet library.

Ethernet-Shield with Poe Module (Arduino)

The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.

Mega Proto-Shield Kit

Proto Shield kit to extend your Arduino Mega with your own wired circuit.

Mega Proto-Shield only PCB (Rev. 3)

Arduino Mega Proto PCB

This is only the PCB from the Arduino Mega Proto Shield, no other parts included.

Motor-Shield (Arduino)

The Arduino Motor Shield is based on the L298, which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors.

Motor-Shield Kit (Arduino)

Motor Control v1.1

We have a list of shields in our roadmap, but so far we have prepared one that allows to control motors from your board. This shield is still under test, but you can take a look at its Schematic, and use it in your designs

Proto-Shield - Wireless

Arduino shield with a socket for wireless modules like Digi Xbee.
Built in 3.3V voltage regulator and prototyping area

Proto-Shield - Wireless SD

Proto-Shield Kit

Proto Shield kit to extend your Arduino with your own wired circuit.

Proto-Shield R3 (assembled)

Shield - Proto

It allows to mount and add your own circuits to Arduino board

Proto-Shield R3 PCB

Shield - Proto

It allows to mount and add your own circuits to Arduino board

TinkerKit - Base Kit

The Base Kit is a pack of different TinkerKit Modules, aimed to start designing interactive enviroments / prototype interfaces without using the breadboard or the soldering iron.

USB 2 Serial Converter (Arduino)

This module transforms the USB port in a COM Port.
It has the same Uno ATMEGA8U2 microcontroller so it could be eventually reprogrammed if you would like to use another communication protocol.

Xbee-Shield

The Xbee shield allows an Arduino board to communicate wirelessly using Zigbee. It is based on the Xbee module from MaxStream. This kit includes one Xbee 2.5 chip antennea module.

Xbee-Shield without Xbee Module

The Xbee shield allows an Arduino board to communicate wirelessly using Zigbee. It is based on the Xbee module from MaxStream. You can buy the Xbee module here: http://www.watterott.com/testshop/en/Interfaces/Xbee-ZigBee