Accessories - JTAG

10-pin to 20-pin JTAG Adapter

A 10-pin to 20-pin JTAG Adapter designed to convert between the ARM mini-JTAG connector (10-pin) and the standard ARM JTAG connector (20-pin).

10-pos IDC Ribbon Cable 50 MIL

DC Ribbon Cable with 10-pos to 10-pos sockets. This cable can be used with the 10-pin mini-JTAG connector

• Connector has 50 mil (1.27 mm) pitch.
• Cable is 85 mm in length.

3.2" Display (QVGA)

4.3" Display (480x272)

7" Display (800x480)

ARM-JTAG-20-10 / 20 - 10 Pin adapter

JTAG 20 PIN 0.1" TO 10 PIN 0.05" ADAPTER

ARM-JTAG-SWD

ARM JTAG SWD Adapter for OpenOCD and Roley Crossworks

ARM-USB-OCD-H JTAG Debugger/Programmer

High Speed 3-in-1 Fast USB ARM JTAG, USB-to-RS232 virtual Port and power supply 5VDC device (Supported by OpenOCD and other OpenSource Debuggers)

ARM-USB-TINY-H JTAG Debugger/Programmer

Low Cost High Speed JTAG Debugger (OpenOCD compatible)

Bus Blaster JTAG debugger

Bus Blaster v2 is an experimental, high-speed JTAG debugger from Dangerous Prototypes. Thanks to a reprogrammable buffer, a simple update over USB makes Bus Blaster v2 compatible with many different JTAG debugger types in the most popular open source software. 

Flyswatter

The Flyswatter is a compact USB to JTAG in-circuit debugger and programmer designed for ARM cores.  It can be used with all ARM processors that are supported by OpenOCD.  It connects via USB to the host PC.  The Flyswatter provides a standard 14-pin JTAG interface as well as a standard RS232 port with support for full modem signals.

Flyswatter - ARM 20-Pin JTAG Adapter Kit

This kit provides an adapter board that converts the Flyswatter's 14-pin JTAG interface into a standard ARM 20-pin JTAG interface.

Flyswatter - BeagleBoard Adapter Kit

This kit provides adapter boards that enable the Flyswatter to interface with the BeagleBoard's JTAG and RS-232 headers.

Flyswatter 2

The Flyswatter2 is a high speed JTAG debugger and programmer designed for ARM and MIPS target boards.  The Flyswatter2 provides a standard 20-pin ARM JTAG interface as well as a RS232 port that can be used to communicate with the target system.

Flyswatter2 ARM20ARM14 - ARM 14-pin JTAG Adapter

The ARM20ARM14 JTAG adapter board converts the Flyswatter2's ARM 20-pin JTAG interface into an ARM 14-pin JTAG interface.

Flyswatter2 ARM20MIPS14 - MIPS 14-pin JTAG Adapter

The ARM20MIPS14 JTAG adapter board converts the Flyswatter2's ARM 20-pin JTAG interface into an MIPS 14-pin JTAG interface.

Flyswatter2 ARM20TI14 - TI 14-pin JTAG Adapter

The ARM20TI14 JTAG adapter board converts the Flyswatter2's ARM 20-pin JTAG interface into a 14-pin JTAG interface for Texas Instruments target boards. 

LPC-Link 2 - JTAG Debugger

LPC-Link 2 is an extensible, stand-alone debug adapter that can be configured to support various development tools and IDEs by downloadable firmwares.

QVGA Display Adapter Kit

Embedded Artists' QVGA Display adapter lets you connect the 3.2 inch QVGA display to the OEM Base Board using the RGB interface. 16-bit color depth is supported. The OEM Base Board is used in the LPC1788 Developer's Kit. This kit contains the display adapter, an IDC Ribbon Cable, and the 3.2 inch QVGA LCD Display.

Signalyzer ARM JTAG Starter Kit

Signalyzer ARM JTAG Starter Kit. All you need to interface to a standard ARM 20-pin JTAG target device or board.

Signalyzer H4

Signalyzer H series is the next generation of our versatile Signalyzer Tool. Two fully independent and configurable channels provide support for most popular serial protocols (JTAG, SPI, I2C, UART), parallel asynchronous and synchronous interfaces, bit-bang mode. With the modularity in design and the continuously growing range of the Accessory modules Signalyzer-H2 is ready for the most challenging tasks in broad range of applications.

Signalyzer LITE

Signalyzer LITE is a low cost JTAG Boundary-Scan interface for ARM based microprocessors and microcontrollers. LITE version of Signalyzer was designed for use with Xverve's Universal Development Platform and to extend its use beyond basic JTAG functionality providing additional UART port and several peripheral pins which can be controlled by the host computer.