AVR / AVR32 / Xmega

Atmega32u4 Breakout Board+

Toss out those FTDI cables and go USB-native with the ATmega32u4. After many months of back-orders, we finally received a shipment of these little guys and are excited to offer our breakout board. The little dev board keeps it simple, with just the bare essentials:

• Atmega32u4 - AVR core with USB capability. 32K flash, 2.5K RAM running at 16MHz
• We put an open-source, avrdude compatible bootloader on there, which takes 4K. You can always remove it
• Standard AVR 6-pin ISP connector for direct programming (when you need the extra space)
• Big Bootload/Reset button
• 500mA fuse on the USB power line
• Power LED and 'user' LED (also indicates when the bootloader is active)
• Fits nicely in any breadboard
• 4 mounting holes

Plug it in, connect a mini-B USB cable and you can start writing code immediately. With the built-in bootloader you don't even need an AVR programmer. We suggest checking out the LUFA library to get started with the USB core as nearly every kind of device has an example already.

For more information, including files, check out the product page including why you'd want to use a Teensy or this board.

ATMEGA8U2 Breakout

The board comes pre-loaded with the SparkFun USB to Serial COM Port firmware. When the board plugs into a USB port, Windows will ask for a driver, point to the driver .inf file found here. The board should now enumerate as a 'SparkFun COM Port' and act the same as the SparkFun FTDI Basic. In other words, you can use it as a USB to serial bridge or you can use it to load code with Arduino. In addition, the pinout on the end of the board is the same as the FTDI Basic, which means you can plug it directly into boards like the Arduino Pro.

DEV-10277

Atmel AT90USBkey2

The AT90USBKey is a low-cost demonstration board based on the AT90USB1287 microcontroller. It allows the quick evaluation of AVR microcontrollers and the AT90USB family. The key simply connects to the USB port of a personal computer to retrieve on-board documentation and run AVR programs.

Atmel ATSTK1000 - AP7000 Eval Board

STK1000 provides a complete AT32AP7000 development environment. The kit has two ethernet ports, a high quality QVGA LCD, a loudspeaker, and connectors for USART, PS/2, VGA, and USB. A expansion header can be used for prototyping.

Atmel AVR Butterfly

AVR Butterfly is an evaluation tool demonstrating the capabilities of the latest AVR Technology. The tool is shipped with preloaded firmware supporting temperature sensing, light measurement, voltage readings and music playback. AVR Butterfly can also be used as a nametag.

Atmel EVK1100 AVR32 - Eval Kit

The EVK1100 is an evaluation kit and development system for the AVR32 AT32UC3A microcontroller.
It is equipped with a rich set of peripherals, memory, and makes it easy to try the full potential of the AVR32 devices.

Atmel EVK1101 AVR32 - Eval Kit

The EVK1101 is an evaluation kit and development system for the AVR32 AT32UC3B microcontroller.
It is equipped with a rich set of peripherals, memory, and makes it easy to try the full potential of the AVR32 devices

Atmel EVK1104 AVR32 - Evalkit

The 32-bit AVR EVK1104 is an evaluation kit for the AT32UC3A3256 which combines Atmels state of art 32-bit AVR microcontroller with an unrivalled selection of communication interface like USB device including On-The-Go functionality, SDcard, NAND flash with ECC and stereo 16-bit DAC.

Atmel EVK1105 AVR32 - Evalkit

The AVR32 EVK1105 is an evaluation kit for the AT32UC3A0512 which demonstrates Atmel’s state-of-the-art AVR32 microcontroller in Hi-Fi audio decoding and streaming applications.

Atmel MEGA-1284P Xplained (ATMEGA1284P-XPLD)

The AVR Xplained kits are great platforms for early evaluation of the capabilities offered by the AVR microcontrollers.
The MEGA-1284P Xplained contain one QTouch button sensor, three mechanical buttons, four LEDs, 3 analog sensors, a UART to USB bridge.
The AVR Xplained expansion headers provide easy access to analog and digital I/O pins. The board is powered by the USB cable and equipped with the standard 10-pin JTAG header that connects to the full range of AVR debuggers.

Atmel NGW100 AVR32 Eval Kit

The NGW100 uses the AT32AP7000 which combines Atmel's state of the art AVR32 Digital Signal Processor CPU with an unrivalled selection of communication interfaces.

Atmel RZ Raven

The RZ RAVEN 2.4 GHz Evaluation and Starter kit enables development, debugging and demonstration of a wide range of lowpower wireless applications including IEEE 802.15.4, 6LoWPAN and ZigBee networks.

Atmel STK600

Atmel STK600 - AVR/AVR32 Evalkit
The Atmel AVR STK600 is a complete starter kit and development system for the AVR and AVR32 flash microcontrollers from ATMEL Corporation.

Atmel UC3-A3 Xplained (AT32UC3A3-XPLD)

The UC3-A3 Xplained features the AT32UC3A3256 device which is optimized for high speed communication and protocol conversion. The AVR device offers a Hi-Speed USB device and mini host, 256KB Flash, 128KB of high speed SRAM, external SDRAM and NAND Flash ports, dual SD card ports and a rich selection of communication ports. The UC3A3 Xplained kit features a Hi-Speed USB Port, one 64Mbit SDRAM, four LEDs, QTouch slider and button, NTC temperature sensor, analog filter, and 4 I/O expansion ports.

Atmel UC3-L0 Xplained (AT32UC3L0-XPLD)

The UC3-L0 Xplained features the AT32UC3L064, which is a picoPower device optimized for low power control applications. The AVR device offers ultra low power consumption, 64 KB of Flash and 16 KB of SRAM, and a rich selection of communication ports. The UC3L0 Xplained kit features four LEDs + one RGB LED, QTouch slider and button, NTC temperature sensor and analog filter, and 4 I/O expansion ports. Because the UC3L064 does not offer a USB port, the kit also features an external USB to UART/I2C bridge (AT32UC3B1256).

Atmel XMEGA-A1 Xplained (AVR-XPLAIN)

Xplain is an easy to use evaluation and demonstration kit for ATxmega128A1, offering a complete hardware for evaluating the highly accurate analog functionality of the device. The ADC can be used to read a temperature sensor and a potentiometer, and the DAC can be used to generate sound on a mono speaker.

ATSTK500

Atmel STK500 - AVR Evalkit
The Atmel AVR STK500 is a starter kit and development system for Atmel's AVR Flash microcontrollers

ATxmega128A1 Breakoutboard

This is a breakout board for the 100-pin TQFP package of Atmel's ATxmega128A1. The ATxmega128A1 is a low power, high performance and peripheral rich CMOS 8/16-bit microcontroller based on the AVR enhanced RISC architecture.

BOB-09546

AVR Stick

The AVR Stick is a simple data logging device that instantiates itself as an HID keyboard and reports the voltages, along with a 'timestamp,' from two pins on an ATtiny85.  The device uses open source firmware availabe from Objective Development (http://www.obdev.at/vusb/) called V-USB to implement the USB 1.1 standard.  The code that runs the application was based on the EasyLogger example application from Objective development

DEV-09147

AVR-CAN - AT90CAN128 dev kit

AVR-CAN is inexpensive way to learn AT90CAN128 microcontroller from Atmel. It's in very compact form 60x55mm and the presence of both CAN and RS232 allow the customer to make bridge between UART and CAN networks. All AVR pins are available on extension connectors and the board can be easy snap-on prototype or other mother board where additional circuits are built.

AVR-MT-128

DEVELOPMENT BOARD FOR ATMEGA128 AVR MICROCONTROLLER WITH JTAG AND STKxxx COMPATIBLE 10 PIN ICS.

AVR-P28 - AVR Development Board

AVR Development Board for 28 pin AVR controller

AVR-P28-8MHz - Proto Board for 28 Pin Atmel AVR

AVR microcontroller prototype board for 28 pin devices with STKxxx compatible 10 pin ICSP

AVR-T32U4

ARDUINO Leonardo like board with ATMEGA32U4.

AVR32 PIKO Board

AVR32 Module with Atmel AT32UC3B0512 Microcontroller

Olimexino-32U4 (Arduino Leonardo compatible)

ARDUINO Leonardo like board with ATMEGA32U4.

PicoBoard

The PicoBoard allows you to create interactions with various sensors. Using the Scratch programming language, you can easily create simple interactive programs based on the input from sensors. The PicoBoard incorporates a light sensor, sound sensor, a button and a slider, as well as 4 additional inputs that can sense electrical resistance via included cables.

Teensy USB Board v2.0 - ATMEGA32U4

The Teensy USB Development Board is a complete USB-based microcontoller development system. Only a standard Mini-B USB cable (sold separately) is needed to connect to a PC or Macintosh.

All Teensy boards are shipped assembled and fully tested.

Actual size is 1.2 by 0.7 inch

Teensy++ USB Board v2.0 - AT90USB1286

The Teensy++ USB Development Board standard Mini-B USB cable (sold separately) is needed to connect to a PC or Macintosh.

All Teensy boards are shipped assembled and fully tested.