Accessories

Arduino and Breadboard Holder

You've been waiting on this forever and here it is! This is a simple plastic plate that holds an Arduino (Duemilanove or Uno) and self adhesive clear breadboard. It makes prototyping projects easier and gives you a solid place to hook things up. The Arduino board snaps in and the breadboard can either be stuck in place or just left floating.

DEV-11235

Arduino Ethernet Shield - PoE module

This Ag9120 module could be used with the Arduino Ethernet shield (newest revision). The PoE module is designed to extract power from a conventional twisted pair Category 5 Ethernet cable, conforming to the IEEE 802.3af Power-over-Ethernet (PoE) standard.

Atmel ATmega328 with Arduino Bootloader

Atmel ATmega328 flashed with Arduino Uno Bootloader

Bluetooth Mate Gold (BT-Serial-Bridge)

The Bluetooth Mate is very similar to our BlueSMiRF modem, but it is designed specifically to be used with our Arduino Pros and LilyPad Arduinos. These modems work as a serial (RX/TX) pipe, and are a great wireless replacement for serial cables. Any serial stream from 9600 to 115200bps can be passed seamlessly from your computer to your target. We've tested these units successfully over open air at 350ft (106m)!

WRL-09358

Box for Arduino

Box for Arduino: Plastic (flame retardant) box that could fit an Arduino Board (Duemilanove-Diecimila-NG or MEGA), an ETH shield and a battery.

Cable USB A - mini USB B 5 pol. - 1,0m

USB cable A connector> B-connector

USB-cable in example to connect your FTDI Basicbreakout with your computer

Cable USB A - mini USB B 5 pol. - 1,8m

USB cable A connector> B-connector

USB-cable in example to connect your FTDI Basicbreakout with your computer

Cable USB A - mini USB B 5 pol. - 3,0m

USB cable A connector> B-connector

USB-cable in example to connect your FTDI Basicbreakout with your computer

Cable USB A - USB B - 1,0m

USB cable A connector> B-connector

USB-cable in example to connect your Arduino Duemilanove / Mega with your computer

Cable USB A - USB B - 1,8m

USB cable A connector> B-connector

USB-cable in example to connect your Arduino Duemilanove / Mega with your computer

Cable USB A - USB B - 3,0m

USB cable A connector> B-connector

USB-cable in example to connect your Arduino Duemilanove / Mega with your computer

Case for Arduino Uno, Duemilanove

Black acrylic box with a transparent cut out on the top.

Crib for Arduino - Arduino Case and Arduino Mega Case

Finally, home-sweet-home for your Arduino projects!  Made from sturdy, lightweight powder-coated aluminum, the Crib for Arduino case can accommodate either an Arduino Duemilanove or Arduino Mega with head room to spare for a shield like an Ethernet shield.  This enclosure weighs only 5.6 oz (159 g) and is structurally very strong.

Ethernet Shield Faceplate - Crib for Arduino

This is a front faceplate that lets your Crib for Arduino accommodate the Arduino and Ethernet Shield in one secure, clean looking, easy to acces package.

PRT-10037

Freeduino Arduino-compatible Runtime board Rev B

Freeduino Arduino-compatible Runtime board Rev. B. PCB designed to host a programmed Arduino microcontroller and deploy a project using the minimum amount of components. Measures only 62 x 39 mm. It is breadboard friendly (a male header installed in the copper side allows a direct plugging of this board to a breadboard).

FTDI Basic Breakout 3.3V

Replacement: FTDI-Breakout-Reloaded-V11

This is a basic breakout board for the FTDI FT232RL USB to serial IC.

DEV-09873

FTDI Basic Breakout 5V

Replacement: FTDI-Breakout-Reloaded-V11

This is a basic breakout board for the FTDI FT232RL USB to serial IC.

DEV-09716

FTDI Breakout Reloaded

This is a basic breakout board for the FTDI FT232RL USB to serial IC.
Switchable between 3.3V and 5V.

Harness for Arduino/Seeeduino kit

Harness Kit includes:

* 9V Battery Case with JST connector
* 2.1mm DC jack with JST connector
* Arduino/Seeeduino Chasis

Harness for Arduino/Seeeduino Mega kit

Harness Kit includes:

9V Battery Case * 1
2.1mm DC jack to pin plug adapter * 1
Arduino/Seeeduino Chasis *

Power Supply 3-12V / 0.3A

For use with Arduino Boards

• Output voltage swicthable (3; 4, 5; 6; 7,5; 9; 12V )
• Controll-LED
• cable length: 1,75m
• Six different output connectors

Power Supply 3-12V / 0.6A

For use with Arduino Boards.

• Output voltage swicthable (3; 4, 5; 6; 7,5; 9;12V )
• Controll-LED
• cable length: 1,75m
• six different output connectors

Power Supply 9V / 0.6A

For use with Arduino Boards

• Output voltage: 9V DC
• Cable length: 1,75m
• Output connector: 5,5mm x 2,1mm

Shield stacking headers

These are standard 10-pin, 8-pin and 6-pin 0.1" spacing female headers...with a twist! The pins are extra long which means you can use these to stack shields

Set contains:

• 1x 10-pin
• 2x 8-pin
• 1x 6-pin

USB 2 Serial Converter (Arduino)

This module transforms the USB port in a COM Port.
It has the same Uno ATMEGA8U2 microcontroller so it could be eventually reprogrammed if you would like to use another communication protocol.