Other


More categories

Adafruit PCB Ruler - 6"

The first time you soldered up a surface mount component you may have been surprised "these are really small parts!" and there's dozens of different names too!

5,53 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Breadboard Power Supply 5V/3.3V

Here is a  simple breadboard power supply kit that takes power from a DC wall wart or an microUSB Port and outputs selectable 5V and 3.3V regulated voltage.
The .1" headers are mounted on the bottom of the PCB for simple insertion into a breadboard. Pins labeled + and - plug directly into the power lines.

10,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

EL Sequencer

The SparkFun EL Sequencer is a board that contains an Arduino-compatible microcontroller, and circuitry for controlling up to eight strands of electroluminescent wire. EL wire is flexible plastic cord that glows brightly when high-voltage AC is applied to it. It’s available in numerous colors (see the related products below), runs cool, and requires very little current, but can be difficult to work with because of the high-voltage requirements. The EL Sequencer can safely switch high-voltage AC on and off, allowing you to easily create animated displays or whatever else your imagination can come up with.

COM-12781

38,51 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Lectro Candle Kit

The LectroCandle is a simple, through-hole kit, comprised mainly of 3 RGB LEDs and an ATtiny85 to control them. Essentially, the Lectro Candle is exactly what it sounds like – an LED-based “candle” that cycles through all the colors of the rainbow. The programming pins of the ATtiny85 are also brought out on the PCB, so you can customize the firmware however you want. This is a perfect kit to start exploring physical computing and play around with LEDs!

KIT-09563

only 9,52 EUR instead 15,88 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Level Shifter 8-Channel (TXB0108)

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V.

8,81 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.



Level-Shifter 4-Channel (bidirectional)

This is our 4 channel Level shifter for connecting i. e. a 3,3V sensor to n 5V microcontroller. The Level-Shifter converts the digital signal to the right voltage.
You can use it from 1,8 - 5V and it can be used with normal serial, I2C, SPI and any other digital signal.

2,00 EUR - 1,50 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Level-Shifter 6-Channel (bidirectional)

This is our 6 channel Level shifter for connecting i. e. a 3.3V sensor to a 5V microcontroller. The Level-Shifter converts the digital signal to the right voltage.
You can use it from 1,8 - 6V and it can be used with normal serial, I2C, SPI and any other digital signal.

2,40 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Level-Shifter 8-Channel (74LVC244)

This is our 8 channel Level shifter based on a 74LVC244 for connecting i. e. a 3.3V sensor to a 5V microcontroller. The Level-Shifter converts the digital signal to the right voltage.

2,95 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Logomatic v2 - Serial SD Datalogger (FAT32)

The SparkFun Logomatic v2 takes everything we learned with multiple logging projects over the years and boils it down to an easy to use device, that is now more adaptable than ever! Version 2 incorporates the LPC2148 with microUSB, battery charging, FAT32 formatting, and microSD support. This allows us to use the SparkFun LPC2148 USB bootloader for even easier and faster modification of the firmware. No programmer required!

WIG-12772

59,98 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.



Make Elektronik - Bauteilset 1 (Einsteiger)

Make: Elektronik
Starter Set für Experiment 1-11

25,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Make Elektronik - Bauteilset 2

Make: Elektronik
Lötset für Experimente 12-14

20,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Make Elektronik - Bauteilset 3

Make: Elektronik
Bauteilset Nr. 3

25,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

MOD-IO

MOD-IO is stackable development board which add analog and digital inputs and outputs to any of our development boards with UEXT. If you work with any of our development boards with UEXT connector and you need more digital and analog iniputs and outputs you can add these by connecting MOD-IO to your development board. This board allow easy interfacing to 4 relays, 4 optoisolated digitl inputs, 4 analog inputs. MOD-IO is stackable and addressable, what does this means? these boards can plug together so you can add as many as you want input and outputs! i.e. 8, 12 etc! MOD-IO have ATmega16 microcontroller and the firmware is available for modification.

30,88 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.



MOD-IO2

MOD-IO2 is stackable development board which adds RELAYs and GPIOs to any of our development boards with UEXT. If you work with any of our development boards with UEXT connector and you need more GPIOs and/or RELAY outputs you can add these by connecting MOD-IO2 to your development board. This board allows easy way to interface up to 2 relays and 7 GPIOs. MOD-IO2 is stackable and addressable, what does this means? These boards can stack together so you can add as many input and outputs as you want! E.g. 2-4-6-8 etc.! MOD-IO2 has PIC16F1503 microcontroller and the firmware is available for modification.

15,41 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Railuino components

Components for Railuino (control Märklin).

5,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

Relay Module (4-Channel 10A)

A Relay is a digital switch to control much higher voltages and currents than your normal Arduino boards does. When inputs a logic voltage, the relay will switch to allow current to flow or cutoff, depending on your wiring. A Relay usually consists of a coil, 1 common terminal, 1 normally closed terminal and one normally open terminal. When the coil is energized, the common terminal and the normally open terminal will have continuity.

4,85 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.



ShiftBar - RGB LED Controller

The ShiftBar is a medium-power RGB LED controller featuring 10-bit digital brightness control on each color channel (over one billion colors). Multiple ShiftBar modules can be chained together and controlled from a single microcontroller to create large LED displays.

8,00 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.



SIM Reader kit

This is a SIM card reader/writer kit for experimentation and investigation of SIM & Smart cards. Once the kit is assenbled, accompanying software can be used to read and write from the card. Together they can be used to backup stored SIM card data, recover deleted SMS's and phone contacts, examine the last 10 phone numbers dialed, etc. (Despite being called a SIM reader, it can also write to SIM cards)

only 15,65 EUR instead 18,06 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SPC56B-Discovery - e200z0h PowerPC

Based on SPC560B54L5, the discovery board includes a JTAG debugger from PLS, LEDs, push buttons and extension headers to connect prototyping boards or additional modules.

only 59,50 EUR instead 107,10 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

TI C2000 Piccolo LaunchPad (LAUNCHXL-F28027)

The C2000 Piccolo LaunchPad is an inexpensive evaluation platform designed to help you leap right into the world of real-time control programming on the C2000 Piccolo microcontrollers.

only 10,00 EUR instead 20,48 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

TV-B-Gone Kit - Universal v1.2

Tired of all those LCD TVs everywhere?
Want a break from advertisements while you're trying to eat?
Want to zap screens from across the street?

The TV-B-Gone kit is what you need! This ultra-high-power, open source kit version of the popular TV-B-Gone is fun to make and even more fun to use. This version can be used in both "North American/Asia" as well as "Europe/UK" areas (basically, the whole world)!

21,86 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.