DC Motor
|
Ardumoto - MotorDriver-Shield (SparkFun)This is a motor shield for Arduino that will control two DC motors.
Based on the L298 H-bridge, the Ardumoto can drive up to 2 amps per
channel. The board takes its power from the same Vin line as the Arduino
board, includes blue and yellow LEDs to indicate active direction, and
all driver lines are diode protected from back EMF.
|
|
DRV8801 Single Brushed DC Motor Driver CarrierThis tiny breakout board for TI’s DRV8801 provides a modern alternative to classic motor drivers such as the L293D, SN754410, and L298N. It can deliver a continuous 1 A (2.8 A peak) to a single motor and offers a wide operating voltage range of 8 to 36 V. The DRV8801 features a simple two-pin speed/direction interface, current-sense feedback, and built-in protection against under-voltage, over-current, and over-temperature. 4,60 EUR incl. 19 % VAT excl. shipping costs
|
|
DRV8833 Dual Motor Driver CarrierThis tiny breakout board for TI’s DRV8833 dual motor driver can deliver
1.2 A per channel continuously (2 A peak) to a pair of DC motors. With
an operating voltage range from 2.7 to 10.8 V and built-in protection
against reverse-voltage, under-voltage, over-current, and
over-temperature, this driver is a great solution for powering small,
low-voltage motors.
|
|
DRV8835 Dual Motor Driver CarrierThis tiny breakout board for TI’s DRV8835 dual motor driver can deliver 1.2 A per channel continuously (1.5 A peak) to a pair of DC motors, and it supports two possible control interfaces for added flexibility of use: IN/IN and PHASE/ENABLE. With an operating voltage range from 2 to 11 V and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature, this driver is a great solution for powering up to two small, low-voltage motors. The carrier board has the form factor of a 14-pin DIP package, which makes it easy to use with standard solderless breadboards and 0.1″ perfboards. 5,66 EUR incl. 19 % VAT excl. shipping costs
|
|
Dual MC33926 Motor Driver CarrierThis dual brushed DC motor driver, based on Freescale’s MC33926 full H-bridge, has a wide operating range of 5 – 28 V and can deliver almost 3 A continuously (5 A peak) to each of its two motor channels. The MC33926 works with 3 – 5 V logic levels, supports ultrasonic (up to 20 kHz) PWM, and features current feedback, under-voltage protection, over-current protection, and over-temperature protection. 36,57 EUR incl. 19 % VAT excl. shipping costs
|
|
Dual Motor Driver 14A VNH2SP30 (MD03A)The Pololu high-power motor driver is a compact carrier for two VNH2SP30 motor driver integrated circuits from ST. The board incorporates most of the components of the typical application diagram on page 8 of the VNH2SP30 datasheet, including pull-up and current-limiting resistors and a FET for reverse battery protection. All you need to add is a microcontroller or other control circuit to turn the H-Bridge on and off. 59,50 EUR incl. 19 % VAT excl. shipping costs
|
|
|
Dual Motor Driver 9A VNH3SP30 (MD03A)This carrier board for ST’s VNH3SP30 motor driver IC operates from 5.5 to 16 V and can deliver a continuous 9 A (30 A peak). It offers built-in protection against reverse-voltage, over-voltage, under-voltage, over-temperature, and over-current and makes a great general-purpose motor driver. 47,60 EUR incl. 19 % VAT excl. shipping costs
|
|
High-Power Motor Driver 36v9The Pololu 9 Amp high-power motor driver is a discrete MOSFET
H-bridge designed to drive one DC brushed motor. The H-bridge is
made up
of one N-channel MOSFET per leg, and most of
the board’s
performance is determined by these MOSFETs (the rest of the board
contains the
circuitry to take user inputs and control the MOSFETs). The board
supports a
wide 5.5 to 50 V voltage range and is efficient enough to deliver a
continuous 9 A without a heat sink, or 12 A with a heat sink.
|
|
MC33926 Motor Driver CarrierThis breakout board for Freescale’s MC33926 full H-bridge has an operating range of 5 – 28 V and can deliver almost 3 A continuously (5 A peak) to a DC motor. The MC33926 works with 3 – 5 V logic levels, supports ultrasonic (up to 20 kHz) PWM, and features current feedback, under-voltage protection, over-current protection, and over-temperature protection. 20,65 EUR incl. 19 % VAT excl. shipping costs
|
|
Monster Moto Shield (SparkFun)This is essentially a ramped up version
of our Ardumoto motor driver shield. For this monster shield we've
replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor
drivers. We've also beefed up the support circuitry so this board is
capable of driving a pair of high-current motors! The VIN and motor out
are pitched for our 5mm screw terminals (not included), making it easy
to connect larger gauge wires.
|
|
Motor Driver 14A VNH2SP30 (MD01B)The Pololu high-power motor driver is a compact carrier for the VNH2SP30 motor driver integrated circuits from ST. The board incorporates most of the components of the typical application diagram on page 8 of the VNH2SP30 datasheet, including pull-up and current-limiting resistors and a FET for reverse battery protection. All you need to add is a microcontroller or other control circuit to turn the H-Bridge on and off. 34,94 EUR incl. 19 % VAT excl. shipping costs
|
|
Motor Driver 15A FDS5672 (36v15)The Pololu 20 Amp high-power motor driver is a discrete MOSFET
H-bridge designed to drive one DC brushed motor. The H-bridge is
made up
of one N-channel MOSFET per leg, and most of
the board’s
performance is determined by these MOSFETs (the rest of the board
contains the
circuitry to take user inputs and control the MOSFETs). The board
supports a
wide 5.5 to 40 V voltage range and is efficient enough to deliver a
continuous 20 A without a heat sink, or 28 A with a heat sink.
|
|
Motor Driver 15A IRF7862PBF (18v15)The Pololu 15 Amp high-power motor driver is a discrete MOSFET H-bridge designed to drive one DC brushed motor. The H-bridge is made up of one N-channel MOSFET per leg, and most of the board’s performance is determined by these MOSFETs (the rest of the board contains the circuitry to take user inputs and control the MOSFETs). 30,95 EUR incl. 19 % VAT excl. shipping costs
|
|
Motor Driver 1A Dual TB6612FNGThe TB6612FNG motor driver can control up to two DC motors at a constant current
of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the
motor in one of four function modes - CW, CCW, short-brake, and stop.
|
|
|
Motor Driver 20A IRF7842PBF (24v20)The Pololu 20 Amp high-power motor driver is a discrete MOSFET
H-bridge designed to drive one DC brushed motor. The H-bridge is
made up
of one N-channel MOSFET per leg, and most of
the board’s
performance is determined by these MOSFETs (the rest of the board
contains the
circuitry to take user inputs and control the MOSFETs). The board
supports a
wide 5.5 to 40 V voltage range and is efficient enough to deliver a
continuous 20 A without a heat sink, or 28 A with a heat sink.
|
|
|
Motor Driver 25A IRF8734 (18v25)This discrete MOSFET H-bridge motor driver enables bidirectional control
of one high-power DC brushed motor. The little 1.8x0.8-inch board
supports a wide 5.5 to 30 V voltage range and is efficient enough to
deliver a continuous 25 A without a heat sink.
|
|
Motor Driver 25A IRF8734 (18v25) CSThis discrete MOSFET H-bridge motor driver enables bidirectional control
of one high-power DC brushed motor. The little 1.8x0.8-inch board
supports a wide 5.5 to 30 V voltage range and is efficient enough to
deliver a continuous 25 A without a heat sink.
|
|
|
Motor Driver 9A VNH3SP30 (MD01B)The Pololu high-power motor driver is a compact carrier for the VNH3SP30 motor driver integrated circuits from ST. The board incorporates most of the components of the typical application diagram on page 8 of the VNH3SP30 datasheet, including pull-up and current-limiting resistors and a FET for reverse battery protection. All you need to add is a microcontroller or other control circuit to turn the H-Bridge on and off. 26,18 EUR incl. 19 % VAT excl. shipping costs
|
|
Motor Driver Shield - Pololu Dual VNH5019Get your Arduino moving! This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. These great drivers also offer current-sense feedback and accept ultrasonic PWM frequencies for quieter operation. The Arduino pin mappings can all be customized if the defaults are not convenient, and the motor driver control lines are broken out along the left side of the shield for general-purpose use without an Arduino. 57,07 EUR incl. 19 % VAT excl. shipping costs
|
|
OpenServoThis is our version of the OpenServo
open-source servo controller board. It's meant to replace the existing
controller board in any standard servo (~.78 inch servo width). With
this board you can control a servo entirely with I2C/TWI commands rather
than PWM, meaning that multiple OpenServos can be controlled with just
two lines! The OpenServo firmware also offers some interesting control
features, such as querying a servo with an unknown position, setting
control gain discretely and on-the-fly, and even querying the
destination of the actuator before it reaches it!
|
|
Pololu High-Power Motor Driver 24v12This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The little 1.3×0.8-inch board supports a wide 5.5 to 40 V voltage range and is efficient enough to deliver a continuous 12 A without a heat sink. 37,95 EUR incl. 19 % VAT excl. shipping costs
|
|
|
Pololu High-Power Motor Driver 36v20 CSThe Pololu high-power motor driver is a discrete MOSFET H-bridge designed to drive large DC brushed motors. The H-bridge is made up of one N-channel MOSFET per leg, and most of the board’s performance is determined by these MOSFETs (the rest of the board contains the circuitry to take user inputs and control the MOSFETs). The MOSFET datasheet is available under the “Resources” tab. The board has an absolute maximum voltage rating of 50 V; higher voltages can permanently destroy the motor driver. Under normal operating conditions, ripple voltage on the supply line can raise the maximum voltage to more than the average or intended voltage, so a safe maximum voltage is approximately 44 V. 56,05 EUR incl. 19 % VAT excl. shipping costs
|
|
Pololu Jrk 12v12 USB Motor Controller with FeedbackThe powerful jrk 12v12 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog voltage, and hobby radio control (RC). The controller can be used as an open-loop speed control or for closed-loop speed or position control. The continuous output current is approximately 12 A (30 A max) and the operating range of 6–16 V (with transient protection up to 40 V). 89,25 EUR - 83,30 EUR incl. 19 % VAT excl. shipping costs
|
|
Pololu Jrk 21v3 USB Motor Controller with FeedbackThe jrk 21v3 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog voltage, and hobby radio control (RC). The controller can be used with feedback for closed-loop speed or position control, or it can be used without feedback as an open-loop speed control. The continuous output current is approximately 3 A in the recommended operating range of 8–28 V, with derated performance down to 5 V and transient protection to 40 V. The board ships with connectors included but not soldered in, allowing for custom installations. 45,69 EUR incl. 19 % VAT excl. shipping costs
|
|
|
Pololu Jrk 21v3 USB Motor Controller with Feedback (assembled)The jrk 21v3 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog voltage, and hobby radio control (RC). The controller can be used with feedback for closed-loop speed or position control, or it can be used without feedback as an open-loop speed control. The continuous output current is approximately 3 A in the recommended operating range of 8–28 V, with derated performance down to 5 V and transient protection to 40 V. The board ships with connectors included but not soldered in, allowing for custom installations. 48,07 EUR incl. 19 % VAT excl. shipping costs
|
|
Pololu Qik 2s12v10 Dual Serial Motor ControllerThis powerful motor controller allows variable speed and direction control of two large, brushed DC motors using a simple serial interface and provides several advanced features, such as motor acceleration control and configurable current limiting. Automatic baud detection up to 115.2 kbps and inputs for both RS-232 and TTL serial make it easy to add motors to your microcontroller- or computer-based project. The operating voltage range is 6 to 16 V; the continuous current per channel is up to 13 A (30 A peak). 68,65 EUR incl. 19 % VAT excl. shipping costs
|
|
Pololu Qik 2s9v1 Dual Serial Motor ControllerThis small, inexpensive motor controller allows variable speed and direction control of two small, brushed DC motors using a simple serial interface, making it easy to add motors to your microcontroller- or computer-based project. The motor supply voltage range is 4.5 to 13.5 V; the continuous current per channel is up to 1 A (3 A peak). The logic supply can be as low as 2.7 V, allowing operation with modern microcontrollers running at 3.3 V. 22,88 EUR incl. 19 % VAT excl. shipping costs
|
|
Pololu Simple High-Power Motor Controller 18v15 (Fully assembled)The Pololu Simple High-Power Motor Controller 18v15 makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 30 V and is efficient enough to deliver a continuous 15 A without a heat sink. It ships with the power capacitor and connectors installed as shown. 38,49 EUR incl. 19 % VAT excl. shipping costs
|
|
Pololu Simple High-Power Motor Controller 18v25The Pololu Simple High-Power Motor Controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 30 V and is efficient enough to deliver a continuous 25 A without a heat sink. It ships with the power capacitor and connectors included but not soldered in, allowing for custom installations. 51,09 EUR incl. 19 % VAT excl. shipping costs
|
|
Pololu Simple High-Power Motor Controller 18v7The Pololu Simple Controller 18v7 makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 30 V and is efficient enough to deliver a continuous 7 A (>30 A peak) without a heat sink. It ships with the power capacitor and connectors installed as shown.s. 29,49 EUR incl. 19 % VAT excl. shipping costs
|
|
Pololu Simple High-Power Motor Controller 18v7 (Fully assembled)The Pololu Simple Controller 18v7 makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 30 V and is efficient enough to deliver a continuous 7 A (>30 A peak) without a heat sink. It ships with the power capacitor and connectors installed as shown.s. 30,95 EUR incl. 19 % VAT excl. shipping costs
|
|
Pololu Simple High-Power Motor Controller 24v12The Pololu Simple High-Power Motor Controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 40 V and is efficient enough to deliver a continuous 23 A without a heat sink. It ships with the power capacitor and connectors included but not soldered in, allowing for custom installations. 40,49 EUR incl. 19 % VAT excl. shipping costs
|
|
|
Pololu Simple High-Power Motor Controller 24v12 (Fully assembled)The Pololu Simple High-Power Motor Controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 40 V and is efficient enough to deliver a continuous 23 A without a heat sink. It ships with the power capacitor and connectors included but not soldered in, allowing for custom installations. 41,95 EUR incl. 19 % VAT excl. shipping costs
|
|
Pololu Simple High-Power Motor Controller 24v23The Pololu Simple High-Power Motor Controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 40 V and is efficient enough to deliver a continuous 23 A without a heat sink. It ships with the power capacitor and connectors included but not soldered in, allowing for custom installations. 54,95 EUR incl. 19 % VAT excl. shipping costs
|
|
VNH5019 Motor Driver CarrierThis carrier board for ST’s VNH5019 motor driver IC operates from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak). It works with 2.5 to 5 V logic levels, supports ultrasonic (up to 20 kHz) PWM, and features current sense feedback (an analog voltage proportional to the motor current). Along with built-in protection against reverse-voltage, over-voltage, under-voltage, over-temperature, and over-current, these features make this product a great general-purpose motor driver. 33,27 EUR incl. 19 % VAT excl. shipping costs
|
Product: 0
Total: 0,00
Login
Fast shipping
Informations
Top products
Motor Driver 1A Dual TB6612FNG
5,95 EUR
DRV8835 Dual Motor Driver Breakout
5,66 EUR
Ardumoto - MotorDriver-Shield (SparkFun)
22,72 EUR
Top offers
Nabduino - Mini Webserver (Arduino kompatibel)
instead 33,00 EUR only 24,95 EUR
FriendlyARM 7" Display für Mini2440/Micro2440
instead 78,54 EUR only 49,95 EUR
Digitales Speicher Oszilloskop Bausatz (DSO 062)
instead 41,95 EUR only 35,70 EUR
