Product from Seeed Studio

125Khz RFID module - UART

RDM 125KHz card mini-module is designed for reading code from 125KHz / 134.2KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc.

Electronic brick - 125Khz RFID Card Reader

Seeed 125K RFID reader is a module used to read uem4100 RFID card information with two output formats: Uart and Wiegand. It has high sensitivity with maximum 7cm sensing distance. The 4pins of Electronic Brick Interface make it be very easily used with Arduino or Seeeduino.

Electronic brick - Starter kit

This is a Starter kit of electronic brick; it includes  basic components and sensors. You can build many interesting projects even if you don't know anyting about soldering,and that makes it the best choice for beginners.

Gameduino a game adapter for microcontrollers

Gameduino is a game adapter for Arduino - or anything else with an SPI interface - built as a single shield that stacks up on top of the Arduino and has plugs for a VGA monitor and stereo speakers.

GPRS Shield (Seeedstudio)

The GPRS (General Packet Radio Service) Shield is a new nonvoice value added service that delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. It is controlled via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands), and fully compatible with Seeeduino/Arduino and Mega. The GPRS Shield has 12 GPIOs 2 PWMs and 1 ADC(They are all 2V8 logic).

GROVE - Starter Bundle

Grove/Stem - Base Shield

This is the new version of Electronic Brick Shield. We standardize all the connectors into 4 pins(Signal 1,Singal 2,VCC and GND) 2mm connectors, which simplify the wiring of electronics projects. The 4pins buckled connectors also make the wiring situation more stable. We build all kinds of Twigs to match up with Stem, still don't you need to worry about the compatibleness between stem and your existing Electronic Bricks.We have many kinks of converter cables(still increasing) to deal with the the compatibleness.This is very similar in fashion to an Arduino shield board, and in fact is used as such with our Seeeduino or Mega board.In v1.0b, we move in the analog connectors a little so that it will fit the higher power connector and USB connector.

Harness for Arduino/Seeeduino kit

Harness Kit includes:

9V Battery Case * 1
2.1mm DC jack to pin plug adapter * 1
Arduino/Seeeduino Chasis *

Harness for Arduino/Seeeduino Mega kit

Harness Kit includes:

9V Battery Case * 1
2.1mm DC jack to pin plug adapter * 1
Arduino/Seeeduino Chasis *

Music Shield

Non-invasive AC current sensor (100A max)

Non-invasive AC current sensor (30A max)

Rainbowduino 328 RGB LED Driver (Arduino compatible)

Rainbowduino is an Arduino compatible controller board with professional LED driving capacity.

RFbee V1.1 - Wireless arduino compatible node

The RFBee is a RF module providing easy and flexible wireless data transmission between devices. It is based on a AVR Atmega168 working as a fully functional Arduino connected via SPI to a TI CC1101 RF transceiver.

Seeeduino Film

Seeeduino FILM is an Arduino compatible development platform for space-sensitive projects. It’s flexible, super slim, with built-in Li-Po charger, suitable to build wearable applications. FILM and other extension FRAMEs could be simply connected via the 20p universal bus like a chain, native 2.54mm pitch pins also enables quick prototyping.

Seeeduino Mega (Arduino compatible)

Seeeduino Mega is a microntrolller board based on ATmega1280, derived from Arduino Mega with changes in pursuit for small form factor, flexibility and functionality.It has 70 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.

Seeeduino Mega Protoshield Kit

This is the 1st Protoshield for Seeeduino MEGA which brought all pins from Seeeduino, even Arduino to the top! With this protoshield, users will find a large prototyping area, you can even use Xbee with this board to make it a Xbee shield.

Seeeduino Stalker 328

Seeeduino Stalker is an extensive Wireless Sensor Network node, with native data logging features and considered modular structure. It could be conveniently used as sensor hub or integrated data collector for monitoring, tracking and etc.

Seeeduino Stalker v2

Seeeduino Stalker is a feature rich Arduino compatible Wireless Sensor Network node. It's modular structure and onboard peripherals makes it convenient to log and time stamp sensor data on a periodic basis. The Seeeduino Stalker is a good candidate for all your tracking, monitoring and control projects.

Seeeduino V3 (Atmega 328P)

Seeeduino is Arduino compatible board. Its design is based on Diecimila scheme, 100% compatible to its existing program, shield and IDEs. On the hardware part, remarkable changes are taken to improve the flexibility and user experience.

Ultra Sonic range measurement module

This  is a non-contact distance measurement module, which is also compatible with electronic brick. It’s designed for easy modular project usage with industrial performance.

USB Infrared Toy v2

Assembled USB infrared remote control receiver/transmitter v2 designed by DangerousPrototypes.com. Use a remote control with your computer, view infrared signals on a logic analyzer, capture and replay remote control buttons, and play TV POWER codes.

TES42756P