Product from SparkFun

14 Channel 20Hz GPS Receiver - Venus638FLPx-L

14 Channel 20Hz GPS Receiver - Venus638FLPx-L

Venus638FLPx is a high performance, low cost, single chip GPS receiver targeting mobile consumer and cellular handset applications. It offers very low power consumption, high sensitivity, and best in class signal acquisition and time-to-first-fix performance.

GPS-10919

34,58 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

16x2 LCD amber on black

16x2 LCD amber on black

This is a 16 character by 2 line display that runs at 3.3V. Utilizes the common ST7066/HD44780 parallel interface (datasheet). Interface code is widely available for many different controllers and systems. You will need ~11 general I/O pins to interface to this LCD screen. Includes amber LED backlight.

LCD-09054

12,40 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

16x2 LCD amber on black (serial enabled 3.3V)

16x2 LCD amber on black (serial enabled 3.3V)

This is the latest evolution of our serial LCD. Included on a single board is a 16x2 LCD and an embedded circuit based around a PIC 16F88. The on-board PIC takes a TTL serial input and prints the characters it receives onto the LCD. The installed firmware also allows for a number of special commands so you can clear the screen, adjust the backlight brightness, turn the display on/off, and more.

LCD-09069

22,61 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

16x2 LCD black on green (serial enabled 5V)

16x2 LCD black on green (serial enabled 5V)

This is the latest evolution of our serial LCD. Included on a single board is a 16x2 LCD and an embedded circuit based around a PIC 16F88. The on-board PIC takes a TTL serial input and prints the characters it receives onto the LCD. The installed firmware also allows for a number of special commands so you can clear the screen, adjust the backlight brightness, turn the display on/off, and more.

LCD-09393

19,97 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

16x2 LCD red on black

16x2 LCD red on black

This is a 16 character by 2 line display that runs at 3.3V. Utilizes the common ST7066/HD44780 parallel interface (datasheet). Interface code is widely available for many different controllers and systems. You will need ~11 general I/O pins to interface to this LCD screen. Includes red LED backlight.

LCD-09051

11,97 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



16x2 LCD red on black (serial enabled 3.3V)

16x2 LCD red on black (serial enabled 3.3V)

This is the latest evolution of our serial LCD. Included on a single board is a 16x2 LCD and an embedded circuit based around a PIC 16F88. The on-board PIC takes a TTL serial input and prints the characters it receives onto the LCD. The installed firmware also allows for a number of special commands so you can clear the screen, adjust the backlight brightness, turn the display on/off, and more.

LCD-09068

22,61 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

16x2 LCD red on black (serial enabled 5V)

16x2 LCD red on black (serial enabled 5V)

This is the latest evolution of our serial LCD. Included on a single board is a 16x2 LCD and an embedded circuit based around a PIC 16F88. The on-board PIC takes a TTL serial input and prints the characters it receives onto the LCD. The installed firmware also allows for a number of special commands so you can clear the screen, adjust the backlight brightness, turn the display on/off, and more.

LCD-09394

21,42 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



16x2 LCD white on black (serial enabled 3.3V)

16x2 LCD white on black (serial enabled 3.3V)

This is the latest evolution of our serial LCD. Included on a single board is a 16x2 LCD and an embedded circuit based around a PIC 16F88. The on-board PIC takes a TTL serial input and prints the characters it receives onto the LCD. The installed firmware also allows for a number of special commands so you can clear the screen, adjust the backlight brightness, turn the display on/off, and more.

LCD-09067

22,61 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

16x2 LCD white on black (serial enabled 5V)

16x2 LCD white on black (serial enabled 5V)

This is the latest evolution of our serial LCD. Included on a single board is a 16x2 LCD and an embedded circuit based around a PIC 16F88. The on-board PIC takes a TTL serial input and prints the characters it receives onto the LCD. The installed firmware also allows for a number of special commands so you can clear the screen, adjust the backlight brightness, turn the display on/off, and more.

LCD-09395

21,42 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

16x2 LCD yellow on blue (serial enabled 5V)

16x2 LCD yellow on blue (serial enabled 5V)

This is the latest evolution of our serial LCD. Included on a single board is a 16x2 LCD and an embedded circuit based around a PIC 16F88. The on-board PIC takes a TTL serial input and prints the characters it receives onto the LCD. The installed firmware also allows for a number of special commands so you can clear the screen, adjust the backlight brightness, turn the display on/off, and more.

LCD-09396

19,97 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

2.4GHz Ceramic Chip Antenna

2.4GHz Ceramic Chip Antenna

This is a monolithic SMD 2.4GHz antenna. Works well for any 2.4GHz application, including WLAN, Home RF, and with Bluetooth®  applications.


WRL-09025

0,82 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

2.4GHz Duck Antenna RP-SMA

2.4GHz Duck Antenna RP-SMA

2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4" long.

WRL-00145

6,88 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

2.4GHz Transceiver IC - nRF24L01

2.4GHz Transceiver IC - nRF24L01

Nordic Semiconductor nRF24L01+. Transceiver chip operating in the 2.4GHz band. Take all the coolness of the nRF2401A and add some extra pipelines, buffers, and an auto-retransmit feature - very nice! The improved '+' version of the nRF24L01 includes more features and better range!

COM-00690

2,90 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



20 Channel GS405 Helical GPS Receiver Connector

20 Channel GS405 Helical GPS Receiver Connector

This is the SMD connector that mates with the GS405 GPS receiver.

GPS-08622

0,82 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

32 Channel San Jose Navigation GPS 5Hz Receiver with Antenna

32 Channel San Jose Navigation GPS 5Hz Receiver with Antenna

The FV-M8 (formerly the EB-85A) is a ridiculously powerful new GPS receiver from San Jose Navigation. This receiver is the first receiver we've seen with a 5Hz update rate, and has an amazing set of features and specs!

GPS-08266

86,42 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



4.3

4.3" PSP Touch Screen

This is a 4-wire resistive analog touch screen. Intended to mate with the 24-Bit PSP display, this unit comes with a handy adhesive backing to stick to the PSP display. 4-wire ribbon with 1mm pitch.

LCD-08448

19,81 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

5V DC to DC Step Up - 2xAA

5V DC to DC Step Up - 2xAA

The is a wonderfully simple 5V power source from Bodhilabs. This unit uses a two AA batteries and generates 5V using a DC to DC step up circuit. A jumper is provided on the unit to disconnect power and includes a terminated (right is red) connector. Perfect for all those 5V applications that need to be small, and run on less than 200mA.

PRT-08249

8,91 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



66 Channel LS20031 GPS 10Hz Receiver

66 Channel LS20031 GPS 10Hz Receiver

The LS20031 GPS receiver is a complete 10Hz GPS smart antenna receiver, that includes an embedded antenna and GPS receiver circuits. This low-cost unit outputs an astounding amount of position information 5 times a second. The receiver is based on the proven technology found in LOCOSYS 66 channel GPS SMD type receivers that use MediaTek chip solution.

GPS-08975

51,86 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

7-Segment Serial Display blue

7-Segment Serial Display blue

55The 7-Segment Serial Display turns the thirteen pins necessary to control a 4-digit 7-segment display into just one or three. The display will give you full control of all digits, decimal points, the colon and the apostrophe. At the heart of the display is an ATMega168 which controls all the serial communications and the 4-digit 7-segment display through an easy to use API

COM-09765

11,20 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

7-Segment Serial Display green

7-Segment Serial Display green

The 7-Segment Serial Display turns the thirteen pins necessary to control a 4-digit 7-segment display into just one or three. The display will give you full control of all digits, decimal points, the colon and the apostrophe. At the heart of the display is an ATMega168 which controls all the serial communications and the 4-digit 7-segment display through an easy to use API

COM-09767

11,20 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

7-Segment Serial Display red

7-Segment Serial Display red

The 7-Segment Serial Display turns the thirteen pins necessary to control a 4-digit 7-segment display into just one or three. The display will give you full control of all digits, decimal points, the colon and the apostrophe. At the heart of the display is an ATMega168 which controls all the serial communications and the 4-digit 7-segment display through an easy to use API

COM-09766

11,20 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

7-Segment Serial Display yellow

7-Segment Serial Display yellow

The 7-Segment Serial Display turns the thirteen pins necessary to control a 4-digit 7-segment display into just one or three. The display will give you full control of all digits, decimal points, the colon and the apostrophe. At the heart of the display is an ATMega168 which controls all the serial communications and the 4-digit 7-segment display through an easy to use API

COM-09764

11,20 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

9 DoF Razor IMU (AHRS compatible)

9 DoF Razor IMU (AHRS compatible)

The 9DOF Razor IMU incorporates three sensors - an ITG-3200 (triple-axis gyro), ADXL345 (triple-axis accelerometer), and HMC58883L  (triple-axis magnetometer) - to give you nine degrees of inertial measurement. The outputs of all sensors are processed by an on-board ATmega328 and output over a serial interface. 

SEN-10736

99,95 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



9 DoF Sensor Stick

9 DoF Sensor Stick

The 9DOF Sensor stick is a very small sensor board with 9 degrees of freedom. It includes the ADXL345 accelerometer, the HMC5883L magnetometer, and the ITG-3200 gyro. The 'stick' has a simple I2C interface and a mounting hole for attaching it to your project. Also, the board is a mere 0.036" thick (0.093" overall), allowing it to be easily mounted in just about any application.

SEN-10724

85,68 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

900/1800 MHz Duck Antenna RP-SMA

900/1800 MHz Duck Antenna RP-SMA

900/1800 MHz Duck Antenna 2dBi with regular RP-SMA RF connector. Perfect for use with the XBee 900MHz units. 50 ohm impedance. 105mm long.

WRL-09143

7,70 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

ACS712 Breakout

ACS712 Breakout

This is a breakout board for the fully integrated Hall Effect based linear ACS712 current sensor. The sensor gives precise current measurement for both AC and DC signals. Thick copper conductor and signal traces allows for survival of the device up to 5 times overcurrent conditions.

BOB-08882

8,15 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

ACS712 Low Current Sensor Breakout

ACS712 Low Current Sensor Breakout

This current sensor gives precise current measurement for both AC and DC signals. These are good sensors for metering and measuring overall power consumption of systems. The ACS712 current sensor measures up to 5A of DC or AC current. We added an opamp gain stage for more sensitive current measurements. By adjusting the gain (from 4.27 to 47) you can measure very small currents.

SEN-08883

12,57 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



Alcohol Gas Sensor MQ-3

Alcohol Gas Sensor MQ-3

This alcohol sensor is suitable for detecting alcohol concentration on your breath, just like your common breathalyzer. It has a high sensitivity and fast response time. Sensor provides an analog resistive output based on alcohol concentration. The drive circuit is very simple, all it needs is one resistor. A simple interface could be a 0-3.3V ADC.

SEN-08880

3,97 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



Analog/Digital MUX Breakout

Analog/Digital MUX Breakout

This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip can be used to connect 16 analog sources (like sensors) to 5 pins on a microcontroller. 4 of the pins must be digital pins, 1 pin must be an analog to digital conversion pin. This allows 16 sensors to operate on only 5 pins of a micro! This is a great way to connect a lot of sensors to a few pins.

BOB-09056

3,96 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Antenna GPS Chip-Scale

Antenna GPS Chip-Scale

That is a GPS chip antenna. Itty-bitty! And we were just as surprised when it picked up just as many satellites as the larger ceramic antennas. The PDOP and VDOP (dilution of precision) of these chip antennas are greater than their ceramic siblings and the gain is not as great (to be expected), but heck, if you can get a lock with this little guy, who cares?

GPS-09131

1,23 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Antenna GPS Embedded SMA

Antenna GPS Embedded SMA

Embedded antenna for small, mobile applications.

GPS-00177

10,09 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Ardubot Bare PCB

Ardubot Bare PCB

The Ardubot PCB can be the foundation of your own Arduino-powered bot. When combined with a few other SparkFun offerings, the Ardubot makes a great mobile testing platform. Or you could just go terrorize the cat and annoy your family and friends. Add some lasers and theme music and you can start your own battle-bot league!

ROB-10185

12,17 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Arduino and Breadboard Holder

Arduino and Breadboard Holder

You've been waiting on this forever and here it is! This is a simple plastic plate that holds an Arduino (Duemilanove or Uno) and self adhesive clear breadboard. It makes prototyping projects easier and gives you a solid place to hook things up. The Arduino board snaps in and the breadboard can either be stuck in place or just left floating.

DEV-10059

3,32 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



Arduino Nano V3.0

Arduino Nano V3.0

Arduino Nano is a surface mount breadboard embedded version with integrated USB. It is a smallest, complete, and breadboard friendly. The Nano was designed and is being produced by Gravitech.

40,00 EUR - 37,50 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Arduino Pro 328 - 3.3V/8MHz

Arduino Pro 328 - 3.3V/8MHz

It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software).

DEV-09221

16,50 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Arduino Pro 328 - 5V/16MHz

Arduino Pro 328 - 5V/16MHz

DEV-10915It's blue! It's skinny! It's the Arduino Pro! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). The power switch was moved to the side of the board (good idea Limor!) to allow control when a shield is attached.

DEV-10915

16,50 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Arduino Pro Mini 328 - 3.3V/8MHz

Arduino Pro Mini 328 - 3.3V/8MHz

It's blue! It's thin (0.8mm)! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader

DEV-09220

14,95 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



Arduino Pro Mini 328 - 5V/16MHz

Arduino Pro Mini 328 - 5V/16MHz

It's blue! It's thin (0.8mm)! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader.

DEV-09218

14,95 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



Ardumoto - MotorDriver-Shield (SparkFun)

Ardumoto - MotorDriver-Shield (SparkFun)

This is a motor shield for Arduino that will control two DC motors. Based on the L298 H-bridge, the Ardumoto can drive up to 2 amps per channel. The board takes its power from the same Vin line as the Arduino board,  includes blue and yellow LEDs to indicate active direction, and all driver lines are diode protected from back EMF.

DEV-09815

21,57 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

ArduPilot Mega (Arduino compatible UAV-Controller)

ArduPilot Mega (Arduino compatible UAV-Controller)

The ArduPilot Mega is the newest version of autopilot board designed by Chris Anderson and Jordi Muñoz of DIY Drones using the ATmega1280.

GPS-09710

47,60 EUR incl. 19 % VAT excl. shipping costs

Nicht lagernd, Ware bereits nachbestellt.



ArduPilot Mega - Arduino Mega compatible UAV Controller

ArduPilot Mega - Arduino Mega compatible UAV Controller

The ArduPilot Mega is the newest version of autopilot board designed by Chris Anderson and Jordi Muñoz of DIY Drones. This latest revision uses the ATmega2560 in place of the ATmega1280.

GPS-10294

50,58 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

ATMEGA8U2 Breakout

ATMEGA8U2 Breakout

The board comes pre-loaded with the SparkFun USB to Serial COM Port firmware. When the board plugs into a USB port, Windows will ask for a driver, point to the driver .inf file found here. The board should now enumerate as a 'SparkFun COM Port' and act the same as the SparkFun FTDI Basic. In other words, you can use it as a USB to serial bridge or you can use it to load code with Arduino. In addition, the pinout on the end of the board is the same as the FTDI Basic, which means you can plug it directly into boards like the Arduino Pro.

DEV-10277

16,74 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Atomic IMU 6 DoF (XBee Ready)

Atomic IMU 6 DoF (XBee Ready)

The 6DOF Atomic is a stripped-down IMU, designed to give good performance at a low price. The unit can run as a hard-wired UART interface (0-3.3V, 115200bps), or optionally with an XBee  RF module, and is powered from a single LiPo (Lithium Polymer) battery.

SEN-09812

99,95 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

ATxmega128A1 Breakoutboard

ATxmega128A1 Breakoutboard

This is a breakout board for the 100-pin TQFP package of Atmel's ATxmega128A1. The ATxmega128A1 is a low power, high performance and peripheral rich CMOS 8/16-bit microcontroller based on the AVR enhanced RISC architecture.

BOB-09546

18,45 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Audio-Sound Module - SOMO-14D

Audio-Sound Module - SOMO-14D

The SOMO-14D is a tiny audio module that can play back stored audio files from a micro-SD memory card. The module supports 4-bit ADPCM audio files (.ad4) with sample rates from 6kHz up to 36kHz. The compact 14-pin module takes up very minimal board space and is ideal for any application that requires embedded audio.

DEV-09534

23,80 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

AVR ISP Programming Adapter

AVR ISP Programming Adapter

This is a simple, but extremely handy board to adapt the common 10-pin ISP programmers to the smaller 6-pin ISP connections.

BOB-08508

1,19 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

AVR Programming Cable

AVR Programming Cable

This is a handy AVR programming cable that incorporates both the 10-pin and 6-pin ISP programming interfaces.

DEV-09215

1,75 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

BarePaint - Conductive Paint (50ml)

BarePaint - Conductive Paint (50ml)

Bare Paint is just like any other water-based paint... except that it's electrically conductive! This means that you can actually paint wires onto things like models, clothes, furniture, walls, almost anything you can think of. Standard acrylic or water-based paints can even be used alongside Bare Paint to act as insulation or to create multi-layer circuitry!

COM-10994

21,60 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Barometric Pressure Sensor - BMP085

Barometric Pressure Sensor - BMP085

The BMP085 is a high-precision, ultra-low power barometric pressure sensor. It offers a measuring range of 300 to 1100 hPa with an absolute accuracy of down to 0.03 hPa. The BMP085 is based on piezo-resistive technology for EMC robustness, high accuracy and linearity as well as long term stability.


COM-09603

7,74 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.

Barometric Pressure Sensor - BMP085 Breakout

Barometric Pressure Sensor - BMP085 Breakout

This is a simple breakout board for the BMP085 high-precision, low-power barometric pressure sensor. The BMP085 offers a measuring range of 300 to 1100 hPa with an absolute accuracy of down to 0.03 hPa. It's based on piezo-resistive technology for EMC robustness, high accuracy and linearity as well as long term stability. This sensor supports a voltage supply between 1.8 and 3.6VDC. It is designed to be connected directly to a micro-controller via the I²C bus

SEN-09694

17,26 EUR incl. 19 % VAT excl. shipping costs

Lagernd, gewöhnlich versandfertig in 24 Stunden.