Stepper

3-axis stepper motor driver Shield for Arduino

The FabScan-Shield is a Arduino plug-on module with 3 TMC2208 SilentStepSticks.  This stepper motor driver lets you control three bipolar stepper motor at up to 1.2 A RMS output current per coil. The input voltage for the driver is from 8 to 35V.

32,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

A4988 Stepper Motor Driver Carrier Black Edition

Our Black Edition A4988 stepper motor driver carrier is a higher-performance drop-in replacement for the original A4988 stepper motor driver carrier. It features a four-layer PCB for better thermal performance, allowing the A4988 microstepping bipolar stepper motor driver to deliver approximately 20% more current than our two-layer version. Like our original carrier, the Black Edition offers adjustable current limiting, overcurrent protection, and five different microstep resolutions. It operates from 8 – 35 V and can deliver up to 2 A per coil with sufficient additional cooling.

8,25 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.



A4988 Stepper Motor Driver Carrier, Black Edition (Header Pins Soldered)

This version of our Black Edition A4988 Stepper Motor Driver Carrier ships with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Please see the Black Edition A4988 Stepper Motor Driver Carrier product page for more information about the driver.

10,25 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.



DRV8834 Stepper Motor Driver Carrier (Low Voltage)

The DRV8834 stepper motor driver carrier is a breakout board for TI’s DRV8834 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 carriers, so it can be used as a drop-in replacement for those boards in many applications. The DRV8834 operates from 2.5–10.8 V, allowing stepper motors to be powered with voltages that are too low for other drivers, and can deliver up to approximately 1.5 A per phase continuously without a heat sink or forced air flow (up to 2 A peak). It features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step).

7,14 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.



Pololu A4983 Stepper Motor Driver Carrier

The A4983 stepper motor driver carrier is a breakout board for Allegro’s easy-to-use A4983 microstepping bipolar stepper motor driver. The driver features adjustable current limiting and five different microstep resolutions. The driver operates from 8 – 35 V and can deliver up to 2 A per coil.

11,85 EUR - 10,47 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.



Pololu A4988 Stepper Motor Driver Carrier

This product is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection.

6,66 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.



SilentStepStick Heatsink 14,5 x 15 x 13

Heatsink  14,5 x 15 x 13 mm specially made for our SilentStepStick stepper motor drivers.

This heatsink has adhesive film on the back so you can mount it very easily.

width: 14,5 mm
length: 15mm
height: 13 mm
 
surface: black anodized

1,19 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick Protector for Stepper Motor Drivers

The SilentStepStick Protector is an addon module for StepStick and Pololu A4988 compatible stepper motor drivers. The board provides flyback diodes (freewheeling diodes) for the motor outputs, so that they are also protected against induction voltages in the unpowered state of the driver.

5,85 EUR - 5,25 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick Tester

With this adapter you can test your SilentStepStick or flash the TMC2208 SilentStepStick with an USB-to-serial converter.

3,50 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2100 - 3D Printer Bundle - 4pcs

The bundle contains:
4x SilentStepStick TMC2100 stepper motor driver (3-5V)

pin headers are included (not soldered)
The SilentStepSticks are for 3D printer controllers with 3,3V or 5V logic level.

36,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2100 - 3D Printer Bundle - 5pcs

The bundle contains:
5x SilentStepStick TMC2100 stepper motor driver (3-5V)
5x heatsink 9 x 9 x 12 mm + thermal tape
The SilentStepSticks are for 3D printer controllers with 3,3V or 5V logic level.

45,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2100 5V - 3D Printer Bundle - 4pcs

The bundle contains:
4x SilentStepStick TMC2100 stepper motor driver 5V
4x heatsink 9 x 9 x 12 mm + thermal tape
The SilentStepSticks are for 3D printer controllers with 5V logic level.

36,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2100 5V - 3D Printer Bundle - 5pcs

The bundle contains:
5x SilentStepStick TMC2100 stepper motor driver 5V
5x heatsink 9 x 9 x 12 mm + thermal tape

The SilentStepSticks are for 3D printer controllers with 5V logic level.

45,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2100 5V Stepper Motor Driver

Stepper Motor Driver based on a Trinamic TMC2100.
- Hardware compatible with StepStick and Pololu A4988
- Step/Dir interface with microstep interpolation (up to 256 microsteps)
- stealthChop - for quiet operation and smooth motion
- spreadCycle - highly dynamic motor control chopper

9,95 EUR - 8,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2100 5V Stepper Motor Driver with soldered Pin Header

Stepper Motor Driver based on a Trinamic TMC2100 with soldered pin headers.
- Hardware compatible with StepStick and Pololu A4988
- Step/Dir interface with microstep interpolation (up to 256 microsteps)
- stealthChop - for quiet operation and smooth motion
- spreadCycle - highly dynamic motor control chopper

11,45 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2100 Stepper Motor Driver

Stepper Motor Driver based on a Trinamic TMC2100.
- Hardware compatible with StepStick and Pololu A4988
- Step/Dir interface with microstep interpolation (up to 256 microsteps)
- stealthChop - for quiet operation and smooth motion
- spreadCycle - highly dynamic motor control chopper

9,95 EUR - 8,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2100 Stepper Motor Driver with soldered Pin Header

Stepper Motor Driver based on a Trinamic TMC2100 with soldered pin headers.
- Hardware compatible with StepStick and Pololu A4988
- Step/Dir interface with microstep interpolation (up to 256 microsteps)
- stealthChop - for quiet operation and smooth motion
- spreadCycle - highly dynamic motor control chopper

11,45 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2130 - 3D Printer Bundle - 4pcs

The bundle contains:

4x SilentStepStick TMC2130 stepper motor driver
4x heatsink 9 x 9 x 12 mm + thermal tape

40,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2130 - 3D Printer Bundle - 5pcs

The bundle contains:

5x SilentStepStick TMC2130 stepper motor driver
5x heatsink 9 x 9 x 12 mm + thermal tape

50,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2130 Stepper Motor Driver

SilentStepStick - Trinamic TMC2130 Stepper Motor Driver with
- stealthChop
- for quiet operation and smooth motion
- spreadCycle
- highly dynamic motor control chopper
- coolStep
- current control for energy savings
- stallGuard
- sensorless motor load detection

10,95 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2130 Stepper Motor Driver with soldered Pin Header

SilentStepStick - Trinamic TMC2130 Stepper Motor Driver with soldered pin headers
- stealthChop
- for quiet operation and smooth motion
- spreadCycle
- highly dynamic motor control chopper
- coolStep
- current control for energy savings
- stallGuard
- sensorless motor load detection

12,45 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2208 - 3D Printer Bundle - 4pcs

The bundle contains:
4x SilentStepStick TMC2208 stepper motor driver
4x heatsink 9 x 9 x 12 mm + thermal tape
The SilentStepSticks are for 3D printer controllers with 3,3V or 5V logic level.

33,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2208 - 3D Printer Bundle - 5pcs

The bundle contains:
5x SilentStepStick TMC2208 stepper motor driver
5x heatsink 9 x 9 x 12 mm + thermal tape
The SilentStepSticks are for 3D printer controllers with 3,3V or 5V logic level.

41,00 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2208 Stepper Motor Driver

Stepper Motor Driver based on a Trinamic TMC2208
- Hardware compatible with StepStick and Pololu A4988
- Step/Dir interface with microstep interpolation (up to 256 microsteps)
- stealthChop2 - for quiet operation and smooth motion
- spreadCycle - highly dynamic motor control chopper

7,95 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

SilentStepStick TMC2208 Stepper Motor Driver with Pin Header

Stepper Motor Driver based on a Trinamic TMC2208 with soldered pin headers
- Hardware compatible with StepStick and Pololu A4988
- Step/Dir interface with microstep interpolation (up to 256 microsteps)
- stealthChop2 - for quiet operation and smooth motion
- spreadCycle - highly dynamic motor control chopper

9,45 EUR incl. 19 % VAT excl. shipping costs

Lagernd, versandfertig in 24 Stunden.

TOS-100 Shield Stepper Motor Driver for Arduino

The TOS-100 is an Arduino compatible Shield capable of driving one bipolar stepper motor up to 1.7A that utilizes the Trinamic Motion Control TMC260 stepper motor driver chip.

28,00 EUR incl. 19 % VAT excl. shipping costs

Nicht auf Lager.